GrubVetter

Zesty Sf

212 6Th St

P

Last inspected: April 3, 2025

Inspection History

April 3, 2025
Routine
Pass
P
114143(d)Provide walls / ceilings using materials that are durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable, and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 114130-114130.5, 114132, 114133, 114137, 114139, 114153, 114163, 114165, 114167, 114169, 114175, 114177, 114180, 114182 - Ensure all equipment is approved, properly installed, clean, and maintained in good repair. Ensure all appliances are NSF-approved, commercial grade, durable, and easily cleanable., 114115 (b,c) - Maintain nonfood contact surfaces clean. Thoroughly clean and degrease the cooking equipment and shelves above cooking equipment., 113953, 113953.1, 113953.2, 114067(f) - Provide soap and single-use towels in dispensers, or a drying device at each handwash sink at all times. Maintain all handwash sinks unobstructed and accessible at all times., 114157, 114159 - Maintain onsite an accurate, easily readable metal probe thermometer suitable for measuring temperature of food shall be available. A display thermometer +/- 2F shall be provided for each hot and cold holding unit of potentially hazardous foods and high temperature warewashing machines., 114254-114254.2 - Administer all pesticides through a state licensed pest control operator. Immediately discontinue the use of unapproved pesticide at the food facility. Store all poisonous substances, detergents, bleaches, and cleaning compounds away from food, utensils, packaging materials, and food-contact surfaces. Provide label to working containers of chemicals taken from bulk supplies with the common name of the material. Provide legible manufacturer's label to containers of poisonous or toxic materials and personal care items.
114266Provide walls / ceilings using materials that are durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable, and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 114130-114130.5, 114132, 114133, 114137, 114139, 114153, 114163, 114165, 114167, 114169, 114175, 114177, 114180, 114182 - Ensure all equipment is approved, properly installed, clean, and maintained in good repair. Ensure all appliances are NSF-approved, commercial grade, durable, and easily cleanable., 114115 (b,c) - Maintain nonfood contact surfaces clean. Thoroughly clean and degrease the cooking equipment and shelves above cooking equipment., 113953, 113953.1, 113953.2, 114067(f) - Provide soap and single-use towels in dispensers, or a drying device at each handwash sink at all times. Maintain all handwash sinks unobstructed and accessible at all times., 114157, 114159 - Maintain onsite an accurate, easily readable metal probe thermometer suitable for measuring temperature of food shall be available. A display thermometer +/- 2F shall be provided for each hot and cold holding unit of potentially hazardous foods and high temperature warewashing machines., 114254-114254.2 - Administer all pesticides through a state licensed pest control operator. Immediately discontinue the use of unapproved pesticide at the food facility. Store all poisonous substances, detergents, bleaches, and cleaning compounds away from food, utensils, packaging materials, and food-contact surfaces. Provide label to working containers of chemicals taken from bulk supplies with the common name of the material. Provide legible manufacturer's label to containers of poisonous or toxic materials and personal care items.
114268Provide walls / ceilings using materials that are durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable, and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 114130-114130.5, 114132, 114133, 114137, 114139, 114153, 114163, 114165, 114167, 114169, 114175, 114177, 114180, 114182 - Ensure all equipment is approved, properly installed, clean, and maintained in good repair. Ensure all appliances are NSF-approved, commercial grade, durable, and easily cleanable., 114115 (b,c) - Maintain nonfood contact surfaces clean. Thoroughly clean and degrease the cooking equipment and shelves above cooking equipment., 113953, 113953.1, 113953.2, 114067(f) - Provide soap and single-use towels in dispensers, or a drying device at each handwash sink at all times. Maintain all handwash sinks unobstructed and accessible at all times., 114157, 114159 - Maintain onsite an accurate, easily readable metal probe thermometer suitable for measuring temperature of food shall be available. A display thermometer +/- 2F shall be provided for each hot and cold holding unit of potentially hazardous foods and high temperature warewashing machines., 114254-114254.2 - Administer all pesticides through a state licensed pest control operator. Immediately discontinue the use of unapproved pesticide at the food facility. Store all poisonous substances, detergents, bleaches, and cleaning compounds away from food, utensils, packaging materials, and food-contact surfaces. Provide label to working containers of chemicals taken from bulk supplies with the common name of the material. Provide legible manufacturer's label to containers of poisonous or toxic materials and personal care items.
114268.1Provide walls / ceilings using materials that are durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable, and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 114130-114130.5, 114132, 114133, 114137, 114139, 114153, 114163, 114165, 114167, 114169, 114175, 114177, 114180, 114182 - Ensure all equipment is approved, properly installed, clean, and maintained in good repair. Ensure all appliances are NSF-approved, commercial grade, durable, and easily cleanable., 114115 (b,c) - Maintain nonfood contact surfaces clean. Thoroughly clean and degrease the cooking equipment and shelves above cooking equipment., 113953, 113953.1, 113953.2, 114067(f) - Provide soap and single-use towels in dispensers, or a drying device at each handwash sink at all times. Maintain all handwash sinks unobstructed and accessible at all times., 114157, 114159 - Maintain onsite an accurate, easily readable metal probe thermometer suitable for measuring temperature of food shall be available. A display thermometer +/- 2F shall be provided for each hot and cold holding unit of potentially hazardous foods and high temperature warewashing machines., 114254-114254.2 - Administer all pesticides through a state licensed pest control operator. Immediately discontinue the use of unapproved pesticide at the food facility. Store all poisonous substances, detergents, bleaches, and cleaning compounds away from food, utensils, packaging materials, and food-contact surfaces. Provide label to working containers of chemicals taken from bulk supplies with the common name of the material. Provide legible manufacturer's label to containers of poisonous or toxic materials and personal care items.
114271Provide walls / ceilings using materials that are durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable, and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 114130-114130.5, 114132, 114133, 114137, 114139, 114153, 114163, 114165, 114167, 114169, 114175, 114177, 114180, 114182 - Ensure all equipment is approved, properly installed, clean, and maintained in good repair. Ensure all appliances are NSF-approved, commercial grade, durable, and easily cleanable., 114115 (b,c) - Maintain nonfood contact surfaces clean. Thoroughly clean and degrease the cooking equipment and shelves above cooking equipment., 113953, 113953.1, 113953.2, 114067(f) - Provide soap and single-use towels in dispensers, or a drying device at each handwash sink at all times. Maintain all handwash sinks unobstructed and accessible at all times., 114157, 114159 - Maintain onsite an accurate, easily readable metal probe thermometer suitable for measuring temperature of food shall be available. A display thermometer +/- 2F shall be provided for each hot and cold holding unit of potentially hazardous foods and high temperature warewashing machines., 114254-114254.2 - Administer all pesticides through a state licensed pest control operator. Immediately discontinue the use of unapproved pesticide at the food facility. Store all poisonous substances, detergents, bleaches, and cleaning compounds away from food, utensils, packaging materials, and food-contact surfaces. Provide label to working containers of chemicals taken from bulk supplies with the common name of the material. Provide legible manufacturer's label to containers of poisonous or toxic materials and personal care items.
114272Provide walls / ceilings using materials that are durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable, and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 114130-114130.5, 114132, 114133, 114137, 114139, 114153, 114163, 114165, 114167, 114169, 114175, 114177, 114180, 114182 - Ensure all equipment is approved, properly installed, clean, and maintained in good repair. Ensure all appliances are NSF-approved, commercial grade, durable, and easily cleanable., 114115 (b,c) - Maintain nonfood contact surfaces clean. Thoroughly clean and degrease the cooking equipment and shelves above cooking equipment., 113953, 113953.1, 113953.2, 114067(f) - Provide soap and single-use towels in dispensers, or a drying device at each handwash sink at all times. Maintain all handwash sinks unobstructed and accessible at all times., 114157, 114159 - Maintain onsite an accurate, easily readable metal probe thermometer suitable for measuring temperature of food shall be available. A display thermometer +/- 2F shall be provided for each hot and cold holding unit of potentially hazardous foods and high temperature warewashing machines., 114254-114254.2 - Administer all pesticides through a state licensed pest control operator. Immediately discontinue the use of unapproved pesticide at the food facility. Store all poisonous substances, detergents, bleaches, and cleaning compounds away from food, utensils, packaging materials, and food-contact surfaces. Provide label to working containers of chemicals taken from bulk supplies with the common name of the material. Provide legible manufacturer's label to containers of poisonous or toxic materials and personal care items.
August 6, 2024
Routine
Pass
P
113980Ensure all food is separated and protected from potential cross contamination. Store produce and ready-to-eat foods completely separate or above raw foods including but not limited to raw eggs, fish, meat, ratites, game animals, and poultry. Provide adequate sneeze-guard protection, a container that has a tight fitting and securely attached lid, or dispense food from an approved mechanical dispenser., 113996, 113998, 114037, 114429, 114429.3, 114429.5 - Keep potentially hazardous foods (PHF) cold at 41°F or below or hot held at 135°F or above. Immediately discontinue storing PHF at room temperature., 114047, 114049, 114051, 114053, 114055, 114069(b) - Elevate all food at least 6 inches off of the floor to prevent contamination. Properly label bulk ingredient/food containers with common name., 113984(d), 114097, 114099.1, 114099.4, 114099.6, 114101(b, c, d), 114105, 114109, 114111, 114113, 11415 (a, b, D), 114117, 114125(b), 114141 - Properly wash, rinse and sanitize all food contact surfaces. Make a 100 ppm bleach sanitizing solution or a 200 ppm quaternary ammonia solution for the third compartment., 113953, 113953.1, 113953.2, 114067(f) - Provide soap and single-use towels in dispensers, or a drying device at each handwash sink at all times. Maintain all handwash sinks unobstructed and accessible at all times., 114157, 114159 - Maintain onsite an accurate, easily readable metal probe thermometer suitable for measuring temperature of food shall be available. A display thermometer +/- 2F shall be provided for each hot and cold holding unit of potentially hazardous foods and high temperature warewashing machines., 114067(f, g), 114099, 114099.3, 114099.5, 114101(a), 114101.1, 114101.2, 114103, 114107, 114125) - Provide an approved warewashing facility. Obtain chlorine test strips to monitor chlorine sanitizer solutions and mechanical dishwasher. Obtain quaternary ammonia test strips to monitor quaternary ammonia sanitizer solutions., 114171, 114189.1, 114190, 114192, 114193, 114193.1, 114199, 114201, 114269 - Protect the potable water supply with a backflow protection device, as required by applicable plumbing codes. All plumbing, plumbing fixtures, and grease interceptors shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Any hose used for conveying potable water shall be of approved materials, labeled, properly stored, and used for no other purpose., 114143(d), 114266, 114268, 114268.1, 114271, 114272 - Provide walls / ceilings using materials that are durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable, and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair., 114018, 114020 - Discontinue thawing potentially hazardous foods at room temperature or in standing water. Use one of the following approved methods: - Under potable running water of sufficient velocity to wash away loose food particles using water no greater than 70°F for no more than 2 hours. - In a refrigeration unit at 41°F or below - In a microwave - As part of the cooking process
113984 (aEnsure all food is separated and protected from potential cross contamination. Store produce and ready-to-eat foods completely separate or above raw foods including but not limited to raw eggs, fish, meat, ratites, game animals, and poultry. Provide adequate sneeze-guard protection, a container that has a tight fitting and securely attached lid, or dispense food from an approved mechanical dispenser., 113996, 113998, 114037, 114429, 114429.3, 114429.5 - Keep potentially hazardous foods (PHF) cold at 41°F or below or hot held at 135°F or above. Immediately discontinue storing PHF at room temperature., 114047, 114049, 114051, 114053, 114055, 114069(b) - Elevate all food at least 6 inches off of the floor to prevent contamination. Properly label bulk ingredient/food containers with common name., 113984(d), 114097, 114099.1, 114099.4, 114099.6, 114101(b, c, d), 114105, 114109, 114111, 114113, 11415 (a, b, D), 114117, 114125(b), 114141 - Properly wash, rinse and sanitize all food contact surfaces. Make a 100 ppm bleach sanitizing solution or a 200 ppm quaternary ammonia solution for the third compartment., 113953, 113953.1, 113953.2, 114067(f) - Provide soap and single-use towels in dispensers, or a drying device at each handwash sink at all times. Maintain all handwash sinks unobstructed and accessible at all times., 114157, 114159 - Maintain onsite an accurate, easily readable metal probe thermometer suitable for measuring temperature of food shall be available. A display thermometer +/- 2F shall be provided for each hot and cold holding unit of potentially hazardous foods and high temperature warewashing machines., 114067(f, g), 114099, 114099.3, 114099.5, 114101(a), 114101.1, 114101.2, 114103, 114107, 114125) - Provide an approved warewashing facility. Obtain chlorine test strips to monitor chlorine sanitizer solutions and mechanical dishwasher. Obtain quaternary ammonia test strips to monitor quaternary ammonia sanitizer solutions., 114171, 114189.1, 114190, 114192, 114193, 114193.1, 114199, 114201, 114269 - Protect the potable water supply with a backflow protection device, as required by applicable plumbing codes. All plumbing, plumbing fixtures, and grease interceptors shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Any hose used for conveying potable water shall be of approved materials, labeled, properly stored, and used for no other purpose., 114143(d), 114266, 114268, 114268.1, 114271, 114272 - Provide walls / ceilings using materials that are durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable, and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair., 114018, 114020 - Discontinue thawing potentially hazardous foods at room temperature or in standing water. Use one of the following approved methods: - Under potable running water of sufficient velocity to wash away loose food particles using water no greater than 70°F for no more than 2 hours. - In a refrigeration unit at 41°F or below - In a microwave - As part of the cooking process
113986Ensure all food is separated and protected from potential cross contamination. Store produce and ready-to-eat foods completely separate or above raw foods including but not limited to raw eggs, fish, meat, ratites, game animals, and poultry. Provide adequate sneeze-guard protection, a container that has a tight fitting and securely attached lid, or dispense food from an approved mechanical dispenser., 113996, 113998, 114037, 114429, 114429.3, 114429.5 - Keep potentially hazardous foods (PHF) cold at 41°F or below or hot held at 135°F or above. Immediately discontinue storing PHF at room temperature., 114047, 114049, 114051, 114053, 114055, 114069(b) - Elevate all food at least 6 inches off of the floor to prevent contamination. Properly label bulk ingredient/food containers with common name., 113984(d), 114097, 114099.1, 114099.4, 114099.6, 114101(b, c, d), 114105, 114109, 114111, 114113, 11415 (a, b, D), 114117, 114125(b), 114141 - Properly wash, rinse and sanitize all food contact surfaces. Make a 100 ppm bleach sanitizing solution or a 200 ppm quaternary ammonia solution for the third compartment., 113953, 113953.1, 113953.2, 114067(f) - Provide soap and single-use towels in dispensers, or a drying device at each handwash sink at all times. Maintain all handwash sinks unobstructed and accessible at all times., 114157, 114159 - Maintain onsite an accurate, easily readable metal probe thermometer suitable for measuring temperature of food shall be available. A display thermometer +/- 2F shall be provided for each hot and cold holding unit of potentially hazardous foods and high temperature warewashing machines., 114067(f, g), 114099, 114099.3, 114099.5, 114101(a), 114101.1, 114101.2, 114103, 114107, 114125) - Provide an approved warewashing facility. Obtain chlorine test strips to monitor chlorine sanitizer solutions and mechanical dishwasher. Obtain quaternary ammonia test strips to monitor quaternary ammonia sanitizer solutions., 114171, 114189.1, 114190, 114192, 114193, 114193.1, 114199, 114201, 114269 - Protect the potable water supply with a backflow protection device, as required by applicable plumbing codes. All plumbing, plumbing fixtures, and grease interceptors shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Any hose used for conveying potable water shall be of approved materials, labeled, properly stored, and used for no other purpose., 114143(d), 114266, 114268, 114268.1, 114271, 114272 - Provide walls / ceilings using materials that are durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable, and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair., 114018, 114020 - Discontinue thawing potentially hazardous foods at room temperature or in standing water. Use one of the following approved methods: - Under potable running water of sufficient velocity to wash away loose food particles using water no greater than 70°F for no more than 2 hours. - In a refrigeration unit at 41°F or below - In a microwave - As part of the cooking process
114060Ensure all food is separated and protected from potential cross contamination. Store produce and ready-to-eat foods completely separate or above raw foods including but not limited to raw eggs, fish, meat, ratites, game animals, and poultry. Provide adequate sneeze-guard protection, a container that has a tight fitting and securely attached lid, or dispense food from an approved mechanical dispenser., 113996, 113998, 114037, 114429, 114429.3, 114429.5 - Keep potentially hazardous foods (PHF) cold at 41°F or below or hot held at 135°F or above. Immediately discontinue storing PHF at room temperature., 114047, 114049, 114051, 114053, 114055, 114069(b) - Elevate all food at least 6 inches off of the floor to prevent contamination. Properly label bulk ingredient/food containers with common name., 113984(d), 114097, 114099.1, 114099.4, 114099.6, 114101(b, c, d), 114105, 114109, 114111, 114113, 11415 (a, b, D), 114117, 114125(b), 114141 - Properly wash, rinse and sanitize all food contact surfaces. Make a 100 ppm bleach sanitizing solution or a 200 ppm quaternary ammonia solution for the third compartment., 113953, 113953.1, 113953.2, 114067(f) - Provide soap and single-use towels in dispensers, or a drying device at each handwash sink at all times. Maintain all handwash sinks unobstructed and accessible at all times., 114157, 114159 - Maintain onsite an accurate, easily readable metal probe thermometer suitable for measuring temperature of food shall be available. A display thermometer +/- 2F shall be provided for each hot and cold holding unit of potentially hazardous foods and high temperature warewashing machines., 114067(f, g), 114099, 114099.3, 114099.5, 114101(a), 114101.1, 114101.2, 114103, 114107, 114125) - Provide an approved warewashing facility. Obtain chlorine test strips to monitor chlorine sanitizer solutions and mechanical dishwasher. Obtain quaternary ammonia test strips to monitor quaternary ammonia sanitizer solutions., 114171, 114189.1, 114190, 114192, 114193, 114193.1, 114199, 114201, 114269 - Protect the potable water supply with a backflow protection device, as required by applicable plumbing codes. All plumbing, plumbing fixtures, and grease interceptors shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Any hose used for conveying potable water shall be of approved materials, labeled, properly stored, and used for no other purpose., 114143(d), 114266, 114268, 114268.1, 114271, 114272 - Provide walls / ceilings using materials that are durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable, and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair., 114018, 114020 - Discontinue thawing potentially hazardous foods at room temperature or in standing water. Use one of the following approved methods: - Under potable running water of sufficient velocity to wash away loose food particles using water no greater than 70°F for no more than 2 hours. - In a refrigeration unit at 41°F or below - In a microwave - As part of the cooking process
114067 (aEnsure all food is separated and protected from potential cross contamination. Store produce and ready-to-eat foods completely separate or above raw foods including but not limited to raw eggs, fish, meat, ratites, game animals, and poultry. Provide adequate sneeze-guard protection, a container that has a tight fitting and securely attached lid, or dispense food from an approved mechanical dispenser., 113996, 113998, 114037, 114429, 114429.3, 114429.5 - Keep potentially hazardous foods (PHF) cold at 41°F or below or hot held at 135°F or above. Immediately discontinue storing PHF at room temperature., 114047, 114049, 114051, 114053, 114055, 114069(b) - Elevate all food at least 6 inches off of the floor to prevent contamination. Properly label bulk ingredient/food containers with common name., 113984(d), 114097, 114099.1, 114099.4, 114099.6, 114101(b, c, d), 114105, 114109, 114111, 114113, 11415 (a, b, D), 114117, 114125(b), 114141 - Properly wash, rinse and sanitize all food contact surfaces. Make a 100 ppm bleach sanitizing solution or a 200 ppm quaternary ammonia solution for the third compartment., 113953, 113953.1, 113953.2, 114067(f) - Provide soap and single-use towels in dispensers, or a drying device at each handwash sink at all times. Maintain all handwash sinks unobstructed and accessible at all times., 114157, 114159 - Maintain onsite an accurate, easily readable metal probe thermometer suitable for measuring temperature of food shall be available. A display thermometer +/- 2F shall be provided for each hot and cold holding unit of potentially hazardous foods and high temperature warewashing machines., 114067(f, g), 114099, 114099.3, 114099.5, 114101(a), 114101.1, 114101.2, 114103, 114107, 114125) - Provide an approved warewashing facility. Obtain chlorine test strips to monitor chlorine sanitizer solutions and mechanical dishwasher. Obtain quaternary ammonia test strips to monitor quaternary ammonia sanitizer solutions., 114171, 114189.1, 114190, 114192, 114193, 114193.1, 114199, 114201, 114269 - Protect the potable water supply with a backflow protection device, as required by applicable plumbing codes. All plumbing, plumbing fixtures, and grease interceptors shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Any hose used for conveying potable water shall be of approved materials, labeled, properly stored, and used for no other purpose., 114143(d), 114266, 114268, 114268.1, 114271, 114272 - Provide walls / ceilings using materials that are durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable, and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair., 114018, 114020 - Discontinue thawing potentially hazardous foods at room temperature or in standing water. Use one of the following approved methods: - Under potable running water of sufficient velocity to wash away loose food particles using water no greater than 70°F for no more than 2 hours. - In a refrigeration unit at 41°F or below - In a microwave - As part of the cooking process
114069Ensure all food is separated and protected from potential cross contamination. Store produce and ready-to-eat foods completely separate or above raw foods including but not limited to raw eggs, fish, meat, ratites, game animals, and poultry. Provide adequate sneeze-guard protection, a container that has a tight fitting and securely attached lid, or dispense food from an approved mechanical dispenser., 113996, 113998, 114037, 114429, 114429.3, 114429.5 - Keep potentially hazardous foods (PHF) cold at 41°F or below or hot held at 135°F or above. Immediately discontinue storing PHF at room temperature., 114047, 114049, 114051, 114053, 114055, 114069(b) - Elevate all food at least 6 inches off of the floor to prevent contamination. Properly label bulk ingredient/food containers with common name., 113984(d), 114097, 114099.1, 114099.4, 114099.6, 114101(b, c, d), 114105, 114109, 114111, 114113, 11415 (a, b, D), 114117, 114125(b), 114141 - Properly wash, rinse and sanitize all food contact surfaces. Make a 100 ppm bleach sanitizing solution or a 200 ppm quaternary ammonia solution for the third compartment., 113953, 113953.1, 113953.2, 114067(f) - Provide soap and single-use towels in dispensers, or a drying device at each handwash sink at all times. Maintain all handwash sinks unobstructed and accessible at all times., 114157, 114159 - Maintain onsite an accurate, easily readable metal probe thermometer suitable for measuring temperature of food shall be available. A display thermometer +/- 2F shall be provided for each hot and cold holding unit of potentially hazardous foods and high temperature warewashing machines., 114067(f, g), 114099, 114099.3, 114099.5, 114101(a), 114101.1, 114101.2, 114103, 114107, 114125) - Provide an approved warewashing facility. Obtain chlorine test strips to monitor chlorine sanitizer solutions and mechanical dishwasher. Obtain quaternary ammonia test strips to monitor quaternary ammonia sanitizer solutions., 114171, 114189.1, 114190, 114192, 114193, 114193.1, 114199, 114201, 114269 - Protect the potable water supply with a backflow protection device, as required by applicable plumbing codes. All plumbing, plumbing fixtures, and grease interceptors shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Any hose used for conveying potable water shall be of approved materials, labeled, properly stored, and used for no other purpose., 114143(d), 114266, 114268, 114268.1, 114271, 114272 - Provide walls / ceilings using materials that are durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable, and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair., 114018, 114020 - Discontinue thawing potentially hazardous foods at room temperature or in standing water. Use one of the following approved methods: - Under potable running water of sufficient velocity to wash away loose food particles using water no greater than 70°F for no more than 2 hours. - In a refrigeration unit at 41°F or below - In a microwave - As part of the cooking process
114073Ensure all food is separated and protected from potential cross contamination. Store produce and ready-to-eat foods completely separate or above raw foods including but not limited to raw eggs, fish, meat, ratites, game animals, and poultry. Provide adequate sneeze-guard protection, a container that has a tight fitting and securely attached lid, or dispense food from an approved mechanical dispenser., 113996, 113998, 114037, 114429, 114429.3, 114429.5 - Keep potentially hazardous foods (PHF) cold at 41°F or below or hot held at 135°F or above. Immediately discontinue storing PHF at room temperature., 114047, 114049, 114051, 114053, 114055, 114069(b) - Elevate all food at least 6 inches off of the floor to prevent contamination. Properly label bulk ingredient/food containers with common name., 113984(d), 114097, 114099.1, 114099.4, 114099.6, 114101(b, c, d), 114105, 114109, 114111, 114113, 11415 (a, b, D), 114117, 114125(b), 114141 - Properly wash, rinse and sanitize all food contact surfaces. Make a 100 ppm bleach sanitizing solution or a 200 ppm quaternary ammonia solution for the third compartment., 113953, 113953.1, 113953.2, 114067(f) - Provide soap and single-use towels in dispensers, or a drying device at each handwash sink at all times. Maintain all handwash sinks unobstructed and accessible at all times., 114157, 114159 - Maintain onsite an accurate, easily readable metal probe thermometer suitable for measuring temperature of food shall be available. A display thermometer +/- 2F shall be provided for each hot and cold holding unit of potentially hazardous foods and high temperature warewashing machines., 114067(f, g), 114099, 114099.3, 114099.5, 114101(a), 114101.1, 114101.2, 114103, 114107, 114125) - Provide an approved warewashing facility. Obtain chlorine test strips to monitor chlorine sanitizer solutions and mechanical dishwasher. Obtain quaternary ammonia test strips to monitor quaternary ammonia sanitizer solutions., 114171, 114189.1, 114190, 114192, 114193, 114193.1, 114199, 114201, 114269 - Protect the potable water supply with a backflow protection device, as required by applicable plumbing codes. All plumbing, plumbing fixtures, and grease interceptors shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Any hose used for conveying potable water shall be of approved materials, labeled, properly stored, and used for no other purpose., 114143(d), 114266, 114268, 114268.1, 114271, 114272 - Provide walls / ceilings using materials that are durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable, and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair., 114018, 114020 - Discontinue thawing potentially hazardous foods at room temperature or in standing water. Use one of the following approved methods: - Under potable running water of sufficient velocity to wash away loose food particles using water no greater than 70°F for no more than 2 hours. - In a refrigeration unit at 41°F or below - In a microwave - As part of the cooking process
114077Ensure all food is separated and protected from potential cross contamination. Store produce and ready-to-eat foods completely separate or above raw foods including but not limited to raw eggs, fish, meat, ratites, game animals, and poultry. Provide adequate sneeze-guard protection, a container that has a tight fitting and securely attached lid, or dispense food from an approved mechanical dispenser., 113996, 113998, 114037, 114429, 114429.3, 114429.5 - Keep potentially hazardous foods (PHF) cold at 41°F or below or hot held at 135°F or above. Immediately discontinue storing PHF at room temperature., 114047, 114049, 114051, 114053, 114055, 114069(b) - Elevate all food at least 6 inches off of the floor to prevent contamination. Properly label bulk ingredient/food containers with common name., 113984(d), 114097, 114099.1, 114099.4, 114099.6, 114101(b, c, d), 114105, 114109, 114111, 114113, 11415 (a, b, D), 114117, 114125(b), 114141 - Properly wash, rinse and sanitize all food contact surfaces. Make a 100 ppm bleach sanitizing solution or a 200 ppm quaternary ammonia solution for the third compartment., 113953, 113953.1, 113953.2, 114067(f) - Provide soap and single-use towels in dispensers, or a drying device at each handwash sink at all times. Maintain all handwash sinks unobstructed and accessible at all times., 114157, 114159 - Maintain onsite an accurate, easily readable metal probe thermometer suitable for measuring temperature of food shall be available. A display thermometer +/- 2F shall be provided for each hot and cold holding unit of potentially hazardous foods and high temperature warewashing machines., 114067(f, g), 114099, 114099.3, 114099.5, 114101(a), 114101.1, 114101.2, 114103, 114107, 114125) - Provide an approved warewashing facility. Obtain chlorine test strips to monitor chlorine sanitizer solutions and mechanical dishwasher. Obtain quaternary ammonia test strips to monitor quaternary ammonia sanitizer solutions., 114171, 114189.1, 114190, 114192, 114193, 114193.1, 114199, 114201, 114269 - Protect the potable water supply with a backflow protection device, as required by applicable plumbing codes. All plumbing, plumbing fixtures, and grease interceptors shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Any hose used for conveying potable water shall be of approved materials, labeled, properly stored, and used for no other purpose., 114143(d), 114266, 114268, 114268.1, 114271, 114272 - Provide walls / ceilings using materials that are durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable, and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair., 114018, 114020 - Discontinue thawing potentially hazardous foods at room temperature or in standing water. Use one of the following approved methods: - Under potable running water of sufficient velocity to wash away loose food particles using water no greater than 70°F for no more than 2 hours. - In a refrigeration unit at 41°F or below - In a microwave - As part of the cooking process
114089.1(c)Ensure all food is separated and protected from potential cross contamination. Store produce and ready-to-eat foods completely separate or above raw foods including but not limited to raw eggs, fish, meat, ratites, game animals, and poultry. Provide adequate sneeze-guard protection, a container that has a tight fitting and securely attached lid, or dispense food from an approved mechanical dispenser., 113996, 113998, 114037, 114429, 114429.3, 114429.5 - Keep potentially hazardous foods (PHF) cold at 41°F or below or hot held at 135°F or above. Immediately discontinue storing PHF at room temperature., 114047, 114049, 114051, 114053, 114055, 114069(b) - Elevate all food at least 6 inches off of the floor to prevent contamination. Properly label bulk ingredient/food containers with common name., 113984(d), 114097, 114099.1, 114099.4, 114099.6, 114101(b, c, d), 114105, 114109, 114111, 114113, 11415 (a, b, D), 114117, 114125(b), 114141 - Properly wash, rinse and sanitize all food contact surfaces. Make a 100 ppm bleach sanitizing solution or a 200 ppm quaternary ammonia solution for the third compartment., 113953, 113953.1, 113953.2, 114067(f) - Provide soap and single-use towels in dispensers, or a drying device at each handwash sink at all times. Maintain all handwash sinks unobstructed and accessible at all times., 114157, 114159 - Maintain onsite an accurate, easily readable metal probe thermometer suitable for measuring temperature of food shall be available. A display thermometer +/- 2F shall be provided for each hot and cold holding unit of potentially hazardous foods and high temperature warewashing machines., 114067(f, g), 114099, 114099.3, 114099.5, 114101(a), 114101.1, 114101.2, 114103, 114107, 114125) - Provide an approved warewashing facility. Obtain chlorine test strips to monitor chlorine sanitizer solutions and mechanical dishwasher. Obtain quaternary ammonia test strips to monitor quaternary ammonia sanitizer solutions., 114171, 114189.1, 114190, 114192, 114193, 114193.1, 114199, 114201, 114269 - Protect the potable water supply with a backflow protection device, as required by applicable plumbing codes. All plumbing, plumbing fixtures, and grease interceptors shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Any hose used for conveying potable water shall be of approved materials, labeled, properly stored, and used for no other purpose., 114143(d), 114266, 114268, 114268.1, 114271, 114272 - Provide walls / ceilings using materials that are durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable, and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair., 114018, 114020 - Discontinue thawing potentially hazardous foods at room temperature or in standing water. Use one of the following approved methods: - Under potable running water of sufficient velocity to wash away loose food particles using water no greater than 70°F for no more than 2 hours. - In a refrigeration unit at 41°F or below - In a microwave - As part of the cooking process
114143(c)Ensure all food is separated and protected from potential cross contamination. Store produce and ready-to-eat foods completely separate or above raw foods including but not limited to raw eggs, fish, meat, ratites, game animals, and poultry. Provide adequate sneeze-guard protection, a container that has a tight fitting and securely attached lid, or dispense food from an approved mechanical dispenser., 113996, 113998, 114037, 114429, 114429.3, 114429.5 - Keep potentially hazardous foods (PHF) cold at 41°F or below or hot held at 135°F or above. Immediately discontinue storing PHF at room temperature., 114047, 114049, 114051, 114053, 114055, 114069(b) - Elevate all food at least 6 inches off of the floor to prevent contamination. Properly label bulk ingredient/food containers with common name., 113984(d), 114097, 114099.1, 114099.4, 114099.6, 114101(b, c, d), 114105, 114109, 114111, 114113, 11415 (a, b, D), 114117, 114125(b), 114141 - Properly wash, rinse and sanitize all food contact surfaces. Make a 100 ppm bleach sanitizing solution or a 200 ppm quaternary ammonia solution for the third compartment., 113953, 113953.1, 113953.2, 114067(f) - Provide soap and single-use towels in dispensers, or a drying device at each handwash sink at all times. Maintain all handwash sinks unobstructed and accessible at all times., 114157, 114159 - Maintain onsite an accurate, easily readable metal probe thermometer suitable for measuring temperature of food shall be available. A display thermometer +/- 2F shall be provided for each hot and cold holding unit of potentially hazardous foods and high temperature warewashing machines., 114067(f, g), 114099, 114099.3, 114099.5, 114101(a), 114101.1, 114101.2, 114103, 114107, 114125) - Provide an approved warewashing facility. Obtain chlorine test strips to monitor chlorine sanitizer solutions and mechanical dishwasher. Obtain quaternary ammonia test strips to monitor quaternary ammonia sanitizer solutions., 114171, 114189.1, 114190, 114192, 114193, 114193.1, 114199, 114201, 114269 - Protect the potable water supply with a backflow protection device, as required by applicable plumbing codes. All plumbing, plumbing fixtures, and grease interceptors shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Any hose used for conveying potable water shall be of approved materials, labeled, properly stored, and used for no other purpose., 114143(d), 114266, 114268, 114268.1, 114271, 114272 - Provide walls / ceilings using materials that are durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable, and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair., 114018, 114020 - Discontinue thawing potentially hazardous foods at room temperature or in standing water. Use one of the following approved methods: - Under potable running water of sufficient velocity to wash away loose food particles using water no greater than 70°F for no more than 2 hours. - In a refrigeration unit at 41°F or below - In a microwave - As part of the cooking process
January 23, 2024
Routine
Pass
P
114143(d)Provide walls / ceilings using materials that are durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable, and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair.
114266Provide walls / ceilings using materials that are durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable, and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair.
114268Provide walls / ceilings using materials that are durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable, and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair.
114268.1Provide walls / ceilings using materials that are durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable, and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair.
114271Provide walls / ceilings using materials that are durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable, and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair.
114272Provide walls / ceilings using materials that are durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable, and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair.