Wolfsbane
2495 3Rd St
P
Last inspected: May 28, 2025
Inspection History
May 28, 2025
Pass
P
114193Equipment that discharges liquid waste, e.g. food preparation sinks, dishwashing machines, steam tables, ice machines and bins, espresso machines, walk-in refrigeration units, shall have approved indirect drainage through an air gap into a floor sink or other approved receiving vessel., 114130, 114169 - All equipment shall be installed on castors, six (6) inch high round metal legs, or on a minimum four (4) inch high curb or pedestal with a continuously coved base at the juncture., 114276, 114149, SF Health Code Section 440.5 - Toilet rooms shall be vented to the outside air by means of an openable, screened window, an air shaft, or a light-switch-activated exhaust fan, consistent with the requirements of local building codes., 114271 - Wall and ceiling finish shall be smooth, durable, easily cleanable, and non-absorbent in all areas where there is food service or preparation, open food storage, warewashing, janitorial service, trash storage, and employee restrooms., 114163 - All permanent food facilities that wash, rinse, soak, thaw, or similarly prepare foods shall be provided with a food preparation sink with a single integral drainboard. The food preparation sink shall have a minimum dimension of 18"x18"x12" (LxWxD) with an integral drainboard at least 18"x18" (LxW)., 114256 - Lockers or other suitable facilities shall be located in a designated room or area where contamination of food, equipment, utensils, linens, and single-use articles cannot occur., 114130, 114169 - All new and used equipment and utensils shall be certified or classified for sanitation by an American National Standards Institute (ANSI) accredited certification program, e.g. NSF, ETL Sanitation, UL Sanitation, CSA Sanitation. , 114276, 114149, SF Health Code Section 440.5 - Toilet rooms shall be separated by well-fitted, self-closing doors that prevent the passage of flies, dust or odors., 113953, 113953(b) - Provide minimum 6 inches high side splashguard(s) with rounded corners., 114279, 114281, 114282 - A room, area, or cabinet separated from any food preparation or storage area, or warewashing area shall be provided for the storage of cleaning equipment and supplies., 114271(d) - Conduits of all types shall be installed within walls as practicable. When otherwise installed, they shall be mounted or enclosed so as to facilitate cleaning., 114193, 114193.1, 114269 - Floor surfaces shall be sloped 1:50 to the floor drains., 114279, 114281, 114282 - At least one curbed cleaning facility or janitorial sink equipped with hot and cold water and a drain shall be provided and conveniently located., 114268 - Floor surfaces shall be coved at the juncture of the floor and wall with a 3/8 inch minimum radius coving and shall extend up the wall at least 4 inches., 114193, 114193.1, 114269 - An air gap between the water supply inlet and the flood level rim of the plumbing fixture shall be at least twice the diameter of the water supply inlet and may not be less than 1 inch., 114268 - The floor finish shall be smooth, durable, easily cleanable, and non-absorbent in all areas where there is food service or preparation, open food storage, warewashing, janitorial service, trash storage, and employee restrooms., 114099 - Provide a 3-compartment sink with two integral metal drainboards for manually washing, rinsing, and sanitizing equipment and utensils.
114193.1Equipment that discharges liquid waste, e.g. food preparation sinks, dishwashing machines, steam tables, ice machines and bins, espresso machines, walk-in refrigeration units, shall have approved indirect drainage through an air gap into a floor sink or other approved receiving vessel., 114130, 114169 - All equipment shall be installed on castors, six (6) inch high round metal legs, or on a minimum four (4) inch high curb or pedestal with a continuously coved base at the juncture., 114276, 114149, SF Health Code Section 440.5 - Toilet rooms shall be vented to the outside air by means of an openable, screened window, an air shaft, or a light-switch-activated exhaust fan, consistent with the requirements of local building codes., 114271 - Wall and ceiling finish shall be smooth, durable, easily cleanable, and non-absorbent in all areas where there is food service or preparation, open food storage, warewashing, janitorial service, trash storage, and employee restrooms., 114163 - All permanent food facilities that wash, rinse, soak, thaw, or similarly prepare foods shall be provided with a food preparation sink with a single integral drainboard. The food preparation sink shall have a minimum dimension of 18"x18"x12" (LxWxD) with an integral drainboard at least 18"x18" (LxW)., 114256 - Lockers or other suitable facilities shall be located in a designated room or area where contamination of food, equipment, utensils, linens, and single-use articles cannot occur., 114130, 114169 - All new and used equipment and utensils shall be certified or classified for sanitation by an American National Standards Institute (ANSI) accredited certification program, e.g. NSF, ETL Sanitation, UL Sanitation, CSA Sanitation. , 114276, 114149, SF Health Code Section 440.5 - Toilet rooms shall be separated by well-fitted, self-closing doors that prevent the passage of flies, dust or odors., 113953, 113953(b) - Provide minimum 6 inches high side splashguard(s) with rounded corners., 114279, 114281, 114282 - A room, area, or cabinet separated from any food preparation or storage area, or warewashing area shall be provided for the storage of cleaning equipment and supplies., 114271(d) - Conduits of all types shall be installed within walls as practicable. When otherwise installed, they shall be mounted or enclosed so as to facilitate cleaning., 114193, 114193.1, 114269 - Floor surfaces shall be sloped 1:50 to the floor drains., 114279, 114281, 114282 - At least one curbed cleaning facility or janitorial sink equipped with hot and cold water and a drain shall be provided and conveniently located., 114268 - Floor surfaces shall be coved at the juncture of the floor and wall with a 3/8 inch minimum radius coving and shall extend up the wall at least 4 inches., 114193, 114193.1, 114269 - An air gap between the water supply inlet and the flood level rim of the plumbing fixture shall be at least twice the diameter of the water supply inlet and may not be less than 1 inch., 114268 - The floor finish shall be smooth, durable, easily cleanable, and non-absorbent in all areas where there is food service or preparation, open food storage, warewashing, janitorial service, trash storage, and employee restrooms., 114099 - Provide a 3-compartment sink with two integral metal drainboards for manually washing, rinsing, and sanitizing equipment and utensils.
114269Equipment that discharges liquid waste, e.g. food preparation sinks, dishwashing machines, steam tables, ice machines and bins, espresso machines, walk-in refrigeration units, shall have approved indirect drainage through an air gap into a floor sink or other approved receiving vessel., 114130, 114169 - All equipment shall be installed on castors, six (6) inch high round metal legs, or on a minimum four (4) inch high curb or pedestal with a continuously coved base at the juncture., 114276, 114149, SF Health Code Section 440.5 - Toilet rooms shall be vented to the outside air by means of an openable, screened window, an air shaft, or a light-switch-activated exhaust fan, consistent with the requirements of local building codes., 114271 - Wall and ceiling finish shall be smooth, durable, easily cleanable, and non-absorbent in all areas where there is food service or preparation, open food storage, warewashing, janitorial service, trash storage, and employee restrooms., 114163 - All permanent food facilities that wash, rinse, soak, thaw, or similarly prepare foods shall be provided with a food preparation sink with a single integral drainboard. The food preparation sink shall have a minimum dimension of 18"x18"x12" (LxWxD) with an integral drainboard at least 18"x18" (LxW)., 114256 - Lockers or other suitable facilities shall be located in a designated room or area where contamination of food, equipment, utensils, linens, and single-use articles cannot occur., 114130, 114169 - All new and used equipment and utensils shall be certified or classified for sanitation by an American National Standards Institute (ANSI) accredited certification program, e.g. NSF, ETL Sanitation, UL Sanitation, CSA Sanitation. , 114276, 114149, SF Health Code Section 440.5 - Toilet rooms shall be separated by well-fitted, self-closing doors that prevent the passage of flies, dust or odors., 113953, 113953(b) - Provide minimum 6 inches high side splashguard(s) with rounded corners., 114279, 114281, 114282 - A room, area, or cabinet separated from any food preparation or storage area, or warewashing area shall be provided for the storage of cleaning equipment and supplies., 114271(d) - Conduits of all types shall be installed within walls as practicable. When otherwise installed, they shall be mounted or enclosed so as to facilitate cleaning., 114193, 114193.1, 114269 - Floor surfaces shall be sloped 1:50 to the floor drains., 114279, 114281, 114282 - At least one curbed cleaning facility or janitorial sink equipped with hot and cold water and a drain shall be provided and conveniently located., 114268 - Floor surfaces shall be coved at the juncture of the floor and wall with a 3/8 inch minimum radius coving and shall extend up the wall at least 4 inches., 114193, 114193.1, 114269 - An air gap between the water supply inlet and the flood level rim of the plumbing fixture shall be at least twice the diameter of the water supply inlet and may not be less than 1 inch., 114268 - The floor finish shall be smooth, durable, easily cleanable, and non-absorbent in all areas where there is food service or preparation, open food storage, warewashing, janitorial service, trash storage, and employee restrooms., 114099 - Provide a 3-compartment sink with two integral metal drainboards for manually washing, rinsing, and sanitizing equipment and utensils.
May 28, 2025
Pass
P
114193Equipment that discharges liquid waste, e.g. food preparation sinks, dishwashing machines, steam tables, ice machines and bins, espresso machines, walk-in refrigeration units, shall have approved indirect drainage through an air gap into a floor sink or other approved receiving vessel., 114130, 114169 - All equipment shall be installed on castors, six (6) inch high round metal legs, or on a minimum four (4) inch high curb or pedestal with a continuously coved base at the juncture., 114276, 114149, SF Health Code Section 440.5 - Toilet rooms shall be vented to the outside air by means of an openable, screened window, an air shaft, or a light-switch-activated exhaust fan, consistent with the requirements of local building codes., 114271 - Wall and ceiling finish shall be smooth, durable, easily cleanable, and non-absorbent in all areas where there is food service or preparation, open food storage, warewashing, janitorial service, trash storage, and employee restrooms., 114163 - All permanent food facilities that wash, rinse, soak, thaw, or similarly prepare foods shall be provided with a food preparation sink with a single integral drainboard. The food preparation sink shall have a minimum dimension of 18"x18"x12" (LxWxD) with an integral drainboard at least 18"x18" (LxW)., 114256 - Lockers or other suitable facilities shall be located in a designated room or area where contamination of food, equipment, utensils, linens, and single-use articles cannot occur., 114130, 114169 - All new and used equipment and utensils shall be certified or classified for sanitation by an American National Standards Institute (ANSI) accredited certification program, e.g. NSF, ETL Sanitation, UL Sanitation, CSA Sanitation. , 114276, 114149, SF Health Code Section 440.5 - Toilet rooms shall be separated by well-fitted, self-closing doors that prevent the passage of flies, dust or odors., 113953, 113953(b) - Provide minimum 6 inches high side splashguard(s) with rounded corners., 114279, 114281, 114282 - A room, area, or cabinet separated from any food preparation or storage area, or warewashing area shall be provided for the storage of cleaning equipment and supplies., 114271(d) - Conduits of all types shall be installed within walls as practicable. When otherwise installed, they shall be mounted or enclosed so as to facilitate cleaning., 114193, 114193.1, 114269 - Floor surfaces shall be sloped 1:50 to the floor drains., 114279, 114281, 114282 - At least one curbed cleaning facility or janitorial sink equipped with hot and cold water and a drain shall be provided and conveniently located., 114268 - Floor surfaces shall be coved at the juncture of the floor and wall with a 3/8 inch minimum radius coving and shall extend up the wall at least 4 inches., 114193, 114193.1, 114269 - An air gap between the water supply inlet and the flood level rim of the plumbing fixture shall be at least twice the diameter of the water supply inlet and may not be less than 1 inch., 114268 - The floor finish shall be smooth, durable, easily cleanable, and non-absorbent in all areas where there is food service or preparation, open food storage, warewashing, janitorial service, trash storage, and employee restrooms., 114099 - Provide a 3-compartment sink with two integral metal drainboards for manually washing, rinsing, and sanitizing equipment and utensils.
114193.1Equipment that discharges liquid waste, e.g. food preparation sinks, dishwashing machines, steam tables, ice machines and bins, espresso machines, walk-in refrigeration units, shall have approved indirect drainage through an air gap into a floor sink or other approved receiving vessel., 114130, 114169 - All equipment shall be installed on castors, six (6) inch high round metal legs, or on a minimum four (4) inch high curb or pedestal with a continuously coved base at the juncture., 114276, 114149, SF Health Code Section 440.5 - Toilet rooms shall be vented to the outside air by means of an openable, screened window, an air shaft, or a light-switch-activated exhaust fan, consistent with the requirements of local building codes., 114271 - Wall and ceiling finish shall be smooth, durable, easily cleanable, and non-absorbent in all areas where there is food service or preparation, open food storage, warewashing, janitorial service, trash storage, and employee restrooms., 114163 - All permanent food facilities that wash, rinse, soak, thaw, or similarly prepare foods shall be provided with a food preparation sink with a single integral drainboard. The food preparation sink shall have a minimum dimension of 18"x18"x12" (LxWxD) with an integral drainboard at least 18"x18" (LxW)., 114256 - Lockers or other suitable facilities shall be located in a designated room or area where contamination of food, equipment, utensils, linens, and single-use articles cannot occur., 114130, 114169 - All new and used equipment and utensils shall be certified or classified for sanitation by an American National Standards Institute (ANSI) accredited certification program, e.g. NSF, ETL Sanitation, UL Sanitation, CSA Sanitation. , 114276, 114149, SF Health Code Section 440.5 - Toilet rooms shall be separated by well-fitted, self-closing doors that prevent the passage of flies, dust or odors., 113953, 113953(b) - Provide minimum 6 inches high side splashguard(s) with rounded corners., 114279, 114281, 114282 - A room, area, or cabinet separated from any food preparation or storage area, or warewashing area shall be provided for the storage of cleaning equipment and supplies., 114271(d) - Conduits of all types shall be installed within walls as practicable. When otherwise installed, they shall be mounted or enclosed so as to facilitate cleaning., 114193, 114193.1, 114269 - Floor surfaces shall be sloped 1:50 to the floor drains., 114279, 114281, 114282 - At least one curbed cleaning facility or janitorial sink equipped with hot and cold water and a drain shall be provided and conveniently located., 114268 - Floor surfaces shall be coved at the juncture of the floor and wall with a 3/8 inch minimum radius coving and shall extend up the wall at least 4 inches., 114193, 114193.1, 114269 - An air gap between the water supply inlet and the flood level rim of the plumbing fixture shall be at least twice the diameter of the water supply inlet and may not be less than 1 inch., 114268 - The floor finish shall be smooth, durable, easily cleanable, and non-absorbent in all areas where there is food service or preparation, open food storage, warewashing, janitorial service, trash storage, and employee restrooms., 114099 - Provide a 3-compartment sink with two integral metal drainboards for manually washing, rinsing, and sanitizing equipment and utensils.
114269Equipment that discharges liquid waste, e.g. food preparation sinks, dishwashing machines, steam tables, ice machines and bins, espresso machines, walk-in refrigeration units, shall have approved indirect drainage through an air gap into a floor sink or other approved receiving vessel., 114130, 114169 - All equipment shall be installed on castors, six (6) inch high round metal legs, or on a minimum four (4) inch high curb or pedestal with a continuously coved base at the juncture., 114276, 114149, SF Health Code Section 440.5 - Toilet rooms shall be vented to the outside air by means of an openable, screened window, an air shaft, or a light-switch-activated exhaust fan, consistent with the requirements of local building codes., 114271 - Wall and ceiling finish shall be smooth, durable, easily cleanable, and non-absorbent in all areas where there is food service or preparation, open food storage, warewashing, janitorial service, trash storage, and employee restrooms., 114163 - All permanent food facilities that wash, rinse, soak, thaw, or similarly prepare foods shall be provided with a food preparation sink with a single integral drainboard. The food preparation sink shall have a minimum dimension of 18"x18"x12" (LxWxD) with an integral drainboard at least 18"x18" (LxW)., 114256 - Lockers or other suitable facilities shall be located in a designated room or area where contamination of food, equipment, utensils, linens, and single-use articles cannot occur., 114130, 114169 - All new and used equipment and utensils shall be certified or classified for sanitation by an American National Standards Institute (ANSI) accredited certification program, e.g. NSF, ETL Sanitation, UL Sanitation, CSA Sanitation. , 114276, 114149, SF Health Code Section 440.5 - Toilet rooms shall be separated by well-fitted, self-closing doors that prevent the passage of flies, dust or odors., 113953, 113953(b) - Provide minimum 6 inches high side splashguard(s) with rounded corners., 114279, 114281, 114282 - A room, area, or cabinet separated from any food preparation or storage area, or warewashing area shall be provided for the storage of cleaning equipment and supplies., 114271(d) - Conduits of all types shall be installed within walls as practicable. When otherwise installed, they shall be mounted or enclosed so as to facilitate cleaning., 114193, 114193.1, 114269 - Floor surfaces shall be sloped 1:50 to the floor drains., 114279, 114281, 114282 - At least one curbed cleaning facility or janitorial sink equipped with hot and cold water and a drain shall be provided and conveniently located., 114268 - Floor surfaces shall be coved at the juncture of the floor and wall with a 3/8 inch minimum radius coving and shall extend up the wall at least 4 inches., 114193, 114193.1, 114269 - An air gap between the water supply inlet and the flood level rim of the plumbing fixture shall be at least twice the diameter of the water supply inlet and may not be less than 1 inch., 114268 - The floor finish shall be smooth, durable, easily cleanable, and non-absorbent in all areas where there is food service or preparation, open food storage, warewashing, janitorial service, trash storage, and employee restrooms., 114099 - Provide a 3-compartment sink with two integral metal drainboards for manually washing, rinsing, and sanitizing equipment and utensils.