Taj Indian Cuisine
5701 Geary Blvd
P
Last inspected: February 4, 2026
Inspection History
February 4, 2026
Pass
P
114074All clean and soiled linen shall be properly stored; non-food items shall be stored and displayed separate from food and food-contact surfaces. Utensils and equipment shall be handled and stored so as to be protected from contamination., 114002, 114002.1 - Rapidly cool potentially hazardous foods from 135°F to 70°F within 2 hours, then from 70°F to 41°F within 4 hours. Discontinue cooling PHF's at room temperature. Rapid cool by any of the following approved methods: 1) Ice water bath 2) Ice wand 3) Shallow stainless steel pans filled 2-3 inches and store in refrigerator 4) Separate into smaller or thinner portions and store in refrigerator 5) Blast chiller 6) Any combination of the above. Use the following approved methods provided on the rapid cooling guideline., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 113984(d), 114097, 114099.1, 114099.4, 114099.6, 114101(b, c, d), 114105, 114109, 114111, 114113, 11415 (a, b, D), 114117, 114125(b), 114141 - Properly wash, rinse and sanitize all food contact surfaces. Make a 100 ppm bleach sanitizing solution or a 200 ppm quaternary ammonia solution for the third compartment., 114067(h), 114123, 114143(a, b), 114256-114256.2, 114256.4, 114257-114257.1, 114259, 114259.2-114259.3, 114279, 114281, 114282 - Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 114018, 114020 - Discontinue thawing potentially hazardous foods at room temperature or in standing water. Use one of the following approved methods: - Under potable running water of sufficient velocity to wash away loose food particles using water no greater than 70°F for no more than 2 hours. - In a refrigeration unit at 41°F or below - In a microwave - As part of the cooking process
114081All clean and soiled linen shall be properly stored; non-food items shall be stored and displayed separate from food and food-contact surfaces. Utensils and equipment shall be handled and stored so as to be protected from contamination., 114002, 114002.1 - Rapidly cool potentially hazardous foods from 135°F to 70°F within 2 hours, then from 70°F to 41°F within 4 hours. Discontinue cooling PHF's at room temperature. Rapid cool by any of the following approved methods: 1) Ice water bath 2) Ice wand 3) Shallow stainless steel pans filled 2-3 inches and store in refrigerator 4) Separate into smaller or thinner portions and store in refrigerator 5) Blast chiller 6) Any combination of the above. Use the following approved methods provided on the rapid cooling guideline., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 113984(d), 114097, 114099.1, 114099.4, 114099.6, 114101(b, c, d), 114105, 114109, 114111, 114113, 11415 (a, b, D), 114117, 114125(b), 114141 - Properly wash, rinse and sanitize all food contact surfaces. Make a 100 ppm bleach sanitizing solution or a 200 ppm quaternary ammonia solution for the third compartment., 114067(h), 114123, 114143(a, b), 114256-114256.2, 114256.4, 114257-114257.1, 114259, 114259.2-114259.3, 114279, 114281, 114282 - Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 114018, 114020 - Discontinue thawing potentially hazardous foods at room temperature or in standing water. Use one of the following approved methods: - Under potable running water of sufficient velocity to wash away loose food particles using water no greater than 70°F for no more than 2 hours. - In a refrigeration unit at 41°F or below - In a microwave - As part of the cooking process
114083All clean and soiled linen shall be properly stored; non-food items shall be stored and displayed separate from food and food-contact surfaces. Utensils and equipment shall be handled and stored so as to be protected from contamination., 114002, 114002.1 - Rapidly cool potentially hazardous foods from 135°F to 70°F within 2 hours, then from 70°F to 41°F within 4 hours. Discontinue cooling PHF's at room temperature. Rapid cool by any of the following approved methods: 1) Ice water bath 2) Ice wand 3) Shallow stainless steel pans filled 2-3 inches and store in refrigerator 4) Separate into smaller or thinner portions and store in refrigerator 5) Blast chiller 6) Any combination of the above. Use the following approved methods provided on the rapid cooling guideline., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 113984(d), 114097, 114099.1, 114099.4, 114099.6, 114101(b, c, d), 114105, 114109, 114111, 114113, 11415 (a, b, D), 114117, 114125(b), 114141 - Properly wash, rinse and sanitize all food contact surfaces. Make a 100 ppm bleach sanitizing solution or a 200 ppm quaternary ammonia solution for the third compartment., 114067(h), 114123, 114143(a, b), 114256-114256.2, 114256.4, 114257-114257.1, 114259, 114259.2-114259.3, 114279, 114281, 114282 - Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 114018, 114020 - Discontinue thawing potentially hazardous foods at room temperature or in standing water. Use one of the following approved methods: - Under potable running water of sufficient velocity to wash away loose food particles using water no greater than 70°F for no more than 2 hours. - In a refrigeration unit at 41°F or below - In a microwave - As part of the cooking process
114119All clean and soiled linen shall be properly stored; non-food items shall be stored and displayed separate from food and food-contact surfaces. Utensils and equipment shall be handled and stored so as to be protected from contamination., 114002, 114002.1 - Rapidly cool potentially hazardous foods from 135°F to 70°F within 2 hours, then from 70°F to 41°F within 4 hours. Discontinue cooling PHF's at room temperature. Rapid cool by any of the following approved methods: 1) Ice water bath 2) Ice wand 3) Shallow stainless steel pans filled 2-3 inches and store in refrigerator 4) Separate into smaller or thinner portions and store in refrigerator 5) Blast chiller 6) Any combination of the above. Use the following approved methods provided on the rapid cooling guideline., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 113984(d), 114097, 114099.1, 114099.4, 114099.6, 114101(b, c, d), 114105, 114109, 114111, 114113, 11415 (a, b, D), 114117, 114125(b), 114141 - Properly wash, rinse and sanitize all food contact surfaces. Make a 100 ppm bleach sanitizing solution or a 200 ppm quaternary ammonia solution for the third compartment., 114067(h), 114123, 114143(a, b), 114256-114256.2, 114256.4, 114257-114257.1, 114259, 114259.2-114259.3, 114279, 114281, 114282 - Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 114018, 114020 - Discontinue thawing potentially hazardous foods at room temperature or in standing water. Use one of the following approved methods: - Under potable running water of sufficient velocity to wash away loose food particles using water no greater than 70°F for no more than 2 hours. - In a refrigeration unit at 41°F or below - In a microwave - As part of the cooking process
114121All clean and soiled linen shall be properly stored; non-food items shall be stored and displayed separate from food and food-contact surfaces. Utensils and equipment shall be handled and stored so as to be protected from contamination., 114002, 114002.1 - Rapidly cool potentially hazardous foods from 135°F to 70°F within 2 hours, then from 70°F to 41°F within 4 hours. Discontinue cooling PHF's at room temperature. Rapid cool by any of the following approved methods: 1) Ice water bath 2) Ice wand 3) Shallow stainless steel pans filled 2-3 inches and store in refrigerator 4) Separate into smaller or thinner portions and store in refrigerator 5) Blast chiller 6) Any combination of the above. Use the following approved methods provided on the rapid cooling guideline., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 113984(d), 114097, 114099.1, 114099.4, 114099.6, 114101(b, c, d), 114105, 114109, 114111, 114113, 11415 (a, b, D), 114117, 114125(b), 114141 - Properly wash, rinse and sanitize all food contact surfaces. Make a 100 ppm bleach sanitizing solution or a 200 ppm quaternary ammonia solution for the third compartment., 114067(h), 114123, 114143(a, b), 114256-114256.2, 114256.4, 114257-114257.1, 114259, 114259.2-114259.3, 114279, 114281, 114282 - Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 114018, 114020 - Discontinue thawing potentially hazardous foods at room temperature or in standing water. Use one of the following approved methods: - Under potable running water of sufficient velocity to wash away loose food particles using water no greater than 70°F for no more than 2 hours. - In a refrigeration unit at 41°F or below - In a microwave - As part of the cooking process
114161All clean and soiled linen shall be properly stored; non-food items shall be stored and displayed separate from food and food-contact surfaces. Utensils and equipment shall be handled and stored so as to be protected from contamination., 114002, 114002.1 - Rapidly cool potentially hazardous foods from 135°F to 70°F within 2 hours, then from 70°F to 41°F within 4 hours. Discontinue cooling PHF's at room temperature. Rapid cool by any of the following approved methods: 1) Ice water bath 2) Ice wand 3) Shallow stainless steel pans filled 2-3 inches and store in refrigerator 4) Separate into smaller or thinner portions and store in refrigerator 5) Blast chiller 6) Any combination of the above. Use the following approved methods provided on the rapid cooling guideline., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 113984(d), 114097, 114099.1, 114099.4, 114099.6, 114101(b, c, d), 114105, 114109, 114111, 114113, 11415 (a, b, D), 114117, 114125(b), 114141 - Properly wash, rinse and sanitize all food contact surfaces. Make a 100 ppm bleach sanitizing solution or a 200 ppm quaternary ammonia solution for the third compartment., 114067(h), 114123, 114143(a, b), 114256-114256.2, 114256.4, 114257-114257.1, 114259, 114259.2-114259.3, 114279, 114281, 114282 - Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 114018, 114020 - Discontinue thawing potentially hazardous foods at room temperature or in standing water. Use one of the following approved methods: - Under potable running water of sufficient velocity to wash away loose food particles using water no greater than 70°F for no more than 2 hours. - In a refrigeration unit at 41°F or below - In a microwave - As part of the cooking process
114178All clean and soiled linen shall be properly stored; non-food items shall be stored and displayed separate from food and food-contact surfaces. Utensils and equipment shall be handled and stored so as to be protected from contamination., 114002, 114002.1 - Rapidly cool potentially hazardous foods from 135°F to 70°F within 2 hours, then from 70°F to 41°F within 4 hours. Discontinue cooling PHF's at room temperature. Rapid cool by any of the following approved methods: 1) Ice water bath 2) Ice wand 3) Shallow stainless steel pans filled 2-3 inches and store in refrigerator 4) Separate into smaller or thinner portions and store in refrigerator 5) Blast chiller 6) Any combination of the above. Use the following approved methods provided on the rapid cooling guideline., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 113984(d), 114097, 114099.1, 114099.4, 114099.6, 114101(b, c, d), 114105, 114109, 114111, 114113, 11415 (a, b, D), 114117, 114125(b), 114141 - Properly wash, rinse and sanitize all food contact surfaces. Make a 100 ppm bleach sanitizing solution or a 200 ppm quaternary ammonia solution for the third compartment., 114067(h), 114123, 114143(a, b), 114256-114256.2, 114256.4, 114257-114257.1, 114259, 114259.2-114259.3, 114279, 114281, 114282 - Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 114018, 114020 - Discontinue thawing potentially hazardous foods at room temperature or in standing water. Use one of the following approved methods: - Under potable running water of sufficient velocity to wash away loose food particles using water no greater than 70°F for no more than 2 hours. - In a refrigeration unit at 41°F or below - In a microwave - As part of the cooking process
114179All clean and soiled linen shall be properly stored; non-food items shall be stored and displayed separate from food and food-contact surfaces. Utensils and equipment shall be handled and stored so as to be protected from contamination., 114002, 114002.1 - Rapidly cool potentially hazardous foods from 135°F to 70°F within 2 hours, then from 70°F to 41°F within 4 hours. Discontinue cooling PHF's at room temperature. Rapid cool by any of the following approved methods: 1) Ice water bath 2) Ice wand 3) Shallow stainless steel pans filled 2-3 inches and store in refrigerator 4) Separate into smaller or thinner portions and store in refrigerator 5) Blast chiller 6) Any combination of the above. Use the following approved methods provided on the rapid cooling guideline., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 113984(d), 114097, 114099.1, 114099.4, 114099.6, 114101(b, c, d), 114105, 114109, 114111, 114113, 11415 (a, b, D), 114117, 114125(b), 114141 - Properly wash, rinse and sanitize all food contact surfaces. Make a 100 ppm bleach sanitizing solution or a 200 ppm quaternary ammonia solution for the third compartment., 114067(h), 114123, 114143(a, b), 114256-114256.2, 114256.4, 114257-114257.1, 114259, 114259.2-114259.3, 114279, 114281, 114282 - Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 114018, 114020 - Discontinue thawing potentially hazardous foods at room temperature or in standing water. Use one of the following approved methods: - Under potable running water of sufficient velocity to wash away loose food particles using water no greater than 70°F for no more than 2 hours. - In a refrigeration unit at 41°F or below - In a microwave - As part of the cooking process
114185All clean and soiled linen shall be properly stored; non-food items shall be stored and displayed separate from food and food-contact surfaces. Utensils and equipment shall be handled and stored so as to be protected from contamination., 114002, 114002.1 - Rapidly cool potentially hazardous foods from 135°F to 70°F within 2 hours, then from 70°F to 41°F within 4 hours. Discontinue cooling PHF's at room temperature. Rapid cool by any of the following approved methods: 1) Ice water bath 2) Ice wand 3) Shallow stainless steel pans filled 2-3 inches and store in refrigerator 4) Separate into smaller or thinner portions and store in refrigerator 5) Blast chiller 6) Any combination of the above. Use the following approved methods provided on the rapid cooling guideline., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 113984(d), 114097, 114099.1, 114099.4, 114099.6, 114101(b, c, d), 114105, 114109, 114111, 114113, 11415 (a, b, D), 114117, 114125(b), 114141 - Properly wash, rinse and sanitize all food contact surfaces. Make a 100 ppm bleach sanitizing solution or a 200 ppm quaternary ammonia solution for the third compartment., 114067(h), 114123, 114143(a, b), 114256-114256.2, 114256.4, 114257-114257.1, 114259, 114259.2-114259.3, 114279, 114281, 114282 - Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 114018, 114020 - Discontinue thawing potentially hazardous foods at room temperature or in standing water. Use one of the following approved methods: - Under potable running water of sufficient velocity to wash away loose food particles using water no greater than 70°F for no more than 2 hours. - In a refrigeration unit at 41°F or below - In a microwave - As part of the cooking process
114185.2All clean and soiled linen shall be properly stored; non-food items shall be stored and displayed separate from food and food-contact surfaces. Utensils and equipment shall be handled and stored so as to be protected from contamination., 114002, 114002.1 - Rapidly cool potentially hazardous foods from 135°F to 70°F within 2 hours, then from 70°F to 41°F within 4 hours. Discontinue cooling PHF's at room temperature. Rapid cool by any of the following approved methods: 1) Ice water bath 2) Ice wand 3) Shallow stainless steel pans filled 2-3 inches and store in refrigerator 4) Separate into smaller or thinner portions and store in refrigerator 5) Blast chiller 6) Any combination of the above. Use the following approved methods provided on the rapid cooling guideline., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 113984(d), 114097, 114099.1, 114099.4, 114099.6, 114101(b, c, d), 114105, 114109, 114111, 114113, 11415 (a, b, D), 114117, 114125(b), 114141 - Properly wash, rinse and sanitize all food contact surfaces. Make a 100 ppm bleach sanitizing solution or a 200 ppm quaternary ammonia solution for the third compartment., 114067(h), 114123, 114143(a, b), 114256-114256.2, 114256.4, 114257-114257.1, 114259, 114259.2-114259.3, 114279, 114281, 114282 - Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 114018, 114020 - Discontinue thawing potentially hazardous foods at room temperature or in standing water. Use one of the following approved methods: - Under potable running water of sufficient velocity to wash away loose food particles using water no greater than 70°F for no more than 2 hours. - In a refrigeration unit at 41°F or below - In a microwave - As part of the cooking process
114185.3All clean and soiled linen shall be properly stored; non-food items shall be stored and displayed separate from food and food-contact surfaces. Utensils and equipment shall be handled and stored so as to be protected from contamination., 114002, 114002.1 - Rapidly cool potentially hazardous foods from 135°F to 70°F within 2 hours, then from 70°F to 41°F within 4 hours. Discontinue cooling PHF's at room temperature. Rapid cool by any of the following approved methods: 1) Ice water bath 2) Ice wand 3) Shallow stainless steel pans filled 2-3 inches and store in refrigerator 4) Separate into smaller or thinner portions and store in refrigerator 5) Blast chiller 6) Any combination of the above. Use the following approved methods provided on the rapid cooling guideline., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 113984(d), 114097, 114099.1, 114099.4, 114099.6, 114101(b, c, d), 114105, 114109, 114111, 114113, 11415 (a, b, D), 114117, 114125(b), 114141 - Properly wash, rinse and sanitize all food contact surfaces. Make a 100 ppm bleach sanitizing solution or a 200 ppm quaternary ammonia solution for the third compartment., 114067(h), 114123, 114143(a, b), 114256-114256.2, 114256.4, 114257-114257.1, 114259, 114259.2-114259.3, 114279, 114281, 114282 - Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 114018, 114020 - Discontinue thawing potentially hazardous foods at room temperature or in standing water. Use one of the following approved methods: - Under potable running water of sufficient velocity to wash away loose food particles using water no greater than 70°F for no more than 2 hours. - In a refrigeration unit at 41°F or below - In a microwave - As part of the cooking process
114185.4All clean and soiled linen shall be properly stored; non-food items shall be stored and displayed separate from food and food-contact surfaces. Utensils and equipment shall be handled and stored so as to be protected from contamination., 114002, 114002.1 - Rapidly cool potentially hazardous foods from 135°F to 70°F within 2 hours, then from 70°F to 41°F within 4 hours. Discontinue cooling PHF's at room temperature. Rapid cool by any of the following approved methods: 1) Ice water bath 2) Ice wand 3) Shallow stainless steel pans filled 2-3 inches and store in refrigerator 4) Separate into smaller or thinner portions and store in refrigerator 5) Blast chiller 6) Any combination of the above. Use the following approved methods provided on the rapid cooling guideline., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 113984(d), 114097, 114099.1, 114099.4, 114099.6, 114101(b, c, d), 114105, 114109, 114111, 114113, 11415 (a, b, D), 114117, 114125(b), 114141 - Properly wash, rinse and sanitize all food contact surfaces. Make a 100 ppm bleach sanitizing solution or a 200 ppm quaternary ammonia solution for the third compartment., 114067(h), 114123, 114143(a, b), 114256-114256.2, 114256.4, 114257-114257.1, 114259, 114259.2-114259.3, 114279, 114281, 114282 - Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 114018, 114020 - Discontinue thawing potentially hazardous foods at room temperature or in standing water. Use one of the following approved methods: - Under potable running water of sufficient velocity to wash away loose food particles using water no greater than 70°F for no more than 2 hours. - In a refrigeration unit at 41°F or below - In a microwave - As part of the cooking process
114185.5All clean and soiled linen shall be properly stored; non-food items shall be stored and displayed separate from food and food-contact surfaces. Utensils and equipment shall be handled and stored so as to be protected from contamination., 114002, 114002.1 - Rapidly cool potentially hazardous foods from 135°F to 70°F within 2 hours, then from 70°F to 41°F within 4 hours. Discontinue cooling PHF's at room temperature. Rapid cool by any of the following approved methods: 1) Ice water bath 2) Ice wand 3) Shallow stainless steel pans filled 2-3 inches and store in refrigerator 4) Separate into smaller or thinner portions and store in refrigerator 5) Blast chiller 6) Any combination of the above. Use the following approved methods provided on the rapid cooling guideline., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 113984(d), 114097, 114099.1, 114099.4, 114099.6, 114101(b, c, d), 114105, 114109, 114111, 114113, 11415 (a, b, D), 114117, 114125(b), 114141 - Properly wash, rinse and sanitize all food contact surfaces. Make a 100 ppm bleach sanitizing solution or a 200 ppm quaternary ammonia solution for the third compartment., 114067(h), 114123, 114143(a, b), 114256-114256.2, 114256.4, 114257-114257.1, 114259, 114259.2-114259.3, 114279, 114281, 114282 - Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 114018, 114020 - Discontinue thawing potentially hazardous foods at room temperature or in standing water. Use one of the following approved methods: - Under potable running water of sufficient velocity to wash away loose food particles using water no greater than 70°F for no more than 2 hours. - In a refrigeration unit at 41°F or below - In a microwave - As part of the cooking process
February 4, 2026
Pass
P
114074All clean and soiled linen shall be properly stored; non-food items shall be stored and displayed separate from food and food-contact surfaces. Utensils and equipment shall be handled and stored so as to be protected from contamination., 114002, 114002.1 - Rapidly cool potentially hazardous foods from 135°F to 70°F within 2 hours, then from 70°F to 41°F within 4 hours. Discontinue cooling PHF's at room temperature. Rapid cool by any of the following approved methods: 1) Ice water bath 2) Ice wand 3) Shallow stainless steel pans filled 2-3 inches and store in refrigerator 4) Separate into smaller or thinner portions and store in refrigerator 5) Blast chiller 6) Any combination of the above. Use the following approved methods provided on the rapid cooling guideline., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 113984(d), 114097, 114099.1, 114099.4, 114099.6, 114101(b, c, d), 114105, 114109, 114111, 114113, 11415 (a, b, D), 114117, 114125(b), 114141 - Properly wash, rinse and sanitize all food contact surfaces. Make a 100 ppm bleach sanitizing solution or a 200 ppm quaternary ammonia solution for the third compartment., 114067(h), 114123, 114143(a, b), 114256-114256.2, 114256.4, 114257-114257.1, 114259, 114259.2-114259.3, 114279, 114281, 114282 - Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 114018, 114020 - Discontinue thawing potentially hazardous foods at room temperature or in standing water. Use one of the following approved methods: - Under potable running water of sufficient velocity to wash away loose food particles using water no greater than 70°F for no more than 2 hours. - In a refrigeration unit at 41°F or below - In a microwave - As part of the cooking process
114081All clean and soiled linen shall be properly stored; non-food items shall be stored and displayed separate from food and food-contact surfaces. Utensils and equipment shall be handled and stored so as to be protected from contamination., 114002, 114002.1 - Rapidly cool potentially hazardous foods from 135°F to 70°F within 2 hours, then from 70°F to 41°F within 4 hours. Discontinue cooling PHF's at room temperature. Rapid cool by any of the following approved methods: 1) Ice water bath 2) Ice wand 3) Shallow stainless steel pans filled 2-3 inches and store in refrigerator 4) Separate into smaller or thinner portions and store in refrigerator 5) Blast chiller 6) Any combination of the above. Use the following approved methods provided on the rapid cooling guideline., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 113984(d), 114097, 114099.1, 114099.4, 114099.6, 114101(b, c, d), 114105, 114109, 114111, 114113, 11415 (a, b, D), 114117, 114125(b), 114141 - Properly wash, rinse and sanitize all food contact surfaces. Make a 100 ppm bleach sanitizing solution or a 200 ppm quaternary ammonia solution for the third compartment., 114067(h), 114123, 114143(a, b), 114256-114256.2, 114256.4, 114257-114257.1, 114259, 114259.2-114259.3, 114279, 114281, 114282 - Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 114018, 114020 - Discontinue thawing potentially hazardous foods at room temperature or in standing water. Use one of the following approved methods: - Under potable running water of sufficient velocity to wash away loose food particles using water no greater than 70°F for no more than 2 hours. - In a refrigeration unit at 41°F or below - In a microwave - As part of the cooking process
114083All clean and soiled linen shall be properly stored; non-food items shall be stored and displayed separate from food and food-contact surfaces. Utensils and equipment shall be handled and stored so as to be protected from contamination., 114002, 114002.1 - Rapidly cool potentially hazardous foods from 135°F to 70°F within 2 hours, then from 70°F to 41°F within 4 hours. Discontinue cooling PHF's at room temperature. Rapid cool by any of the following approved methods: 1) Ice water bath 2) Ice wand 3) Shallow stainless steel pans filled 2-3 inches and store in refrigerator 4) Separate into smaller or thinner portions and store in refrigerator 5) Blast chiller 6) Any combination of the above. Use the following approved methods provided on the rapid cooling guideline., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 113984(d), 114097, 114099.1, 114099.4, 114099.6, 114101(b, c, d), 114105, 114109, 114111, 114113, 11415 (a, b, D), 114117, 114125(b), 114141 - Properly wash, rinse and sanitize all food contact surfaces. Make a 100 ppm bleach sanitizing solution or a 200 ppm quaternary ammonia solution for the third compartment., 114067(h), 114123, 114143(a, b), 114256-114256.2, 114256.4, 114257-114257.1, 114259, 114259.2-114259.3, 114279, 114281, 114282 - Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 114018, 114020 - Discontinue thawing potentially hazardous foods at room temperature or in standing water. Use one of the following approved methods: - Under potable running water of sufficient velocity to wash away loose food particles using water no greater than 70°F for no more than 2 hours. - In a refrigeration unit at 41°F or below - In a microwave - As part of the cooking process
114119All clean and soiled linen shall be properly stored; non-food items shall be stored and displayed separate from food and food-contact surfaces. Utensils and equipment shall be handled and stored so as to be protected from contamination., 114002, 114002.1 - Rapidly cool potentially hazardous foods from 135°F to 70°F within 2 hours, then from 70°F to 41°F within 4 hours. Discontinue cooling PHF's at room temperature. Rapid cool by any of the following approved methods: 1) Ice water bath 2) Ice wand 3) Shallow stainless steel pans filled 2-3 inches and store in refrigerator 4) Separate into smaller or thinner portions and store in refrigerator 5) Blast chiller 6) Any combination of the above. Use the following approved methods provided on the rapid cooling guideline., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 113984(d), 114097, 114099.1, 114099.4, 114099.6, 114101(b, c, d), 114105, 114109, 114111, 114113, 11415 (a, b, D), 114117, 114125(b), 114141 - Properly wash, rinse and sanitize all food contact surfaces. Make a 100 ppm bleach sanitizing solution or a 200 ppm quaternary ammonia solution for the third compartment., 114067(h), 114123, 114143(a, b), 114256-114256.2, 114256.4, 114257-114257.1, 114259, 114259.2-114259.3, 114279, 114281, 114282 - Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 114018, 114020 - Discontinue thawing potentially hazardous foods at room temperature or in standing water. Use one of the following approved methods: - Under potable running water of sufficient velocity to wash away loose food particles using water no greater than 70°F for no more than 2 hours. - In a refrigeration unit at 41°F or below - In a microwave - As part of the cooking process
114121All clean and soiled linen shall be properly stored; non-food items shall be stored and displayed separate from food and food-contact surfaces. Utensils and equipment shall be handled and stored so as to be protected from contamination., 114002, 114002.1 - Rapidly cool potentially hazardous foods from 135°F to 70°F within 2 hours, then from 70°F to 41°F within 4 hours. Discontinue cooling PHF's at room temperature. Rapid cool by any of the following approved methods: 1) Ice water bath 2) Ice wand 3) Shallow stainless steel pans filled 2-3 inches and store in refrigerator 4) Separate into smaller or thinner portions and store in refrigerator 5) Blast chiller 6) Any combination of the above. Use the following approved methods provided on the rapid cooling guideline., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 113984(d), 114097, 114099.1, 114099.4, 114099.6, 114101(b, c, d), 114105, 114109, 114111, 114113, 11415 (a, b, D), 114117, 114125(b), 114141 - Properly wash, rinse and sanitize all food contact surfaces. Make a 100 ppm bleach sanitizing solution or a 200 ppm quaternary ammonia solution for the third compartment., 114067(h), 114123, 114143(a, b), 114256-114256.2, 114256.4, 114257-114257.1, 114259, 114259.2-114259.3, 114279, 114281, 114282 - Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 114018, 114020 - Discontinue thawing potentially hazardous foods at room temperature or in standing water. Use one of the following approved methods: - Under potable running water of sufficient velocity to wash away loose food particles using water no greater than 70°F for no more than 2 hours. - In a refrigeration unit at 41°F or below - In a microwave - As part of the cooking process
114161All clean and soiled linen shall be properly stored; non-food items shall be stored and displayed separate from food and food-contact surfaces. Utensils and equipment shall be handled and stored so as to be protected from contamination., 114002, 114002.1 - Rapidly cool potentially hazardous foods from 135°F to 70°F within 2 hours, then from 70°F to 41°F within 4 hours. Discontinue cooling PHF's at room temperature. Rapid cool by any of the following approved methods: 1) Ice water bath 2) Ice wand 3) Shallow stainless steel pans filled 2-3 inches and store in refrigerator 4) Separate into smaller or thinner portions and store in refrigerator 5) Blast chiller 6) Any combination of the above. Use the following approved methods provided on the rapid cooling guideline., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 113984(d), 114097, 114099.1, 114099.4, 114099.6, 114101(b, c, d), 114105, 114109, 114111, 114113, 11415 (a, b, D), 114117, 114125(b), 114141 - Properly wash, rinse and sanitize all food contact surfaces. Make a 100 ppm bleach sanitizing solution or a 200 ppm quaternary ammonia solution for the third compartment., 114067(h), 114123, 114143(a, b), 114256-114256.2, 114256.4, 114257-114257.1, 114259, 114259.2-114259.3, 114279, 114281, 114282 - Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 114018, 114020 - Discontinue thawing potentially hazardous foods at room temperature or in standing water. Use one of the following approved methods: - Under potable running water of sufficient velocity to wash away loose food particles using water no greater than 70°F for no more than 2 hours. - In a refrigeration unit at 41°F or below - In a microwave - As part of the cooking process
114178All clean and soiled linen shall be properly stored; non-food items shall be stored and displayed separate from food and food-contact surfaces. Utensils and equipment shall be handled and stored so as to be protected from contamination., 114002, 114002.1 - Rapidly cool potentially hazardous foods from 135°F to 70°F within 2 hours, then from 70°F to 41°F within 4 hours. Discontinue cooling PHF's at room temperature. Rapid cool by any of the following approved methods: 1) Ice water bath 2) Ice wand 3) Shallow stainless steel pans filled 2-3 inches and store in refrigerator 4) Separate into smaller or thinner portions and store in refrigerator 5) Blast chiller 6) Any combination of the above. Use the following approved methods provided on the rapid cooling guideline., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 113984(d), 114097, 114099.1, 114099.4, 114099.6, 114101(b, c, d), 114105, 114109, 114111, 114113, 11415 (a, b, D), 114117, 114125(b), 114141 - Properly wash, rinse and sanitize all food contact surfaces. Make a 100 ppm bleach sanitizing solution or a 200 ppm quaternary ammonia solution for the third compartment., 114067(h), 114123, 114143(a, b), 114256-114256.2, 114256.4, 114257-114257.1, 114259, 114259.2-114259.3, 114279, 114281, 114282 - Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 114018, 114020 - Discontinue thawing potentially hazardous foods at room temperature or in standing water. Use one of the following approved methods: - Under potable running water of sufficient velocity to wash away loose food particles using water no greater than 70°F for no more than 2 hours. - In a refrigeration unit at 41°F or below - In a microwave - As part of the cooking process
114179All clean and soiled linen shall be properly stored; non-food items shall be stored and displayed separate from food and food-contact surfaces. Utensils and equipment shall be handled and stored so as to be protected from contamination., 114002, 114002.1 - Rapidly cool potentially hazardous foods from 135°F to 70°F within 2 hours, then from 70°F to 41°F within 4 hours. Discontinue cooling PHF's at room temperature. Rapid cool by any of the following approved methods: 1) Ice water bath 2) Ice wand 3) Shallow stainless steel pans filled 2-3 inches and store in refrigerator 4) Separate into smaller or thinner portions and store in refrigerator 5) Blast chiller 6) Any combination of the above. Use the following approved methods provided on the rapid cooling guideline., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 113984(d), 114097, 114099.1, 114099.4, 114099.6, 114101(b, c, d), 114105, 114109, 114111, 114113, 11415 (a, b, D), 114117, 114125(b), 114141 - Properly wash, rinse and sanitize all food contact surfaces. Make a 100 ppm bleach sanitizing solution or a 200 ppm quaternary ammonia solution for the third compartment., 114067(h), 114123, 114143(a, b), 114256-114256.2, 114256.4, 114257-114257.1, 114259, 114259.2-114259.3, 114279, 114281, 114282 - Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 114018, 114020 - Discontinue thawing potentially hazardous foods at room temperature or in standing water. Use one of the following approved methods: - Under potable running water of sufficient velocity to wash away loose food particles using water no greater than 70°F for no more than 2 hours. - In a refrigeration unit at 41°F or below - In a microwave - As part of the cooking process
114185All clean and soiled linen shall be properly stored; non-food items shall be stored and displayed separate from food and food-contact surfaces. Utensils and equipment shall be handled and stored so as to be protected from contamination., 114002, 114002.1 - Rapidly cool potentially hazardous foods from 135°F to 70°F within 2 hours, then from 70°F to 41°F within 4 hours. Discontinue cooling PHF's at room temperature. Rapid cool by any of the following approved methods: 1) Ice water bath 2) Ice wand 3) Shallow stainless steel pans filled 2-3 inches and store in refrigerator 4) Separate into smaller or thinner portions and store in refrigerator 5) Blast chiller 6) Any combination of the above. Use the following approved methods provided on the rapid cooling guideline., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 113984(d), 114097, 114099.1, 114099.4, 114099.6, 114101(b, c, d), 114105, 114109, 114111, 114113, 11415 (a, b, D), 114117, 114125(b), 114141 - Properly wash, rinse and sanitize all food contact surfaces. Make a 100 ppm bleach sanitizing solution or a 200 ppm quaternary ammonia solution for the third compartment., 114067(h), 114123, 114143(a, b), 114256-114256.2, 114256.4, 114257-114257.1, 114259, 114259.2-114259.3, 114279, 114281, 114282 - Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 114018, 114020 - Discontinue thawing potentially hazardous foods at room temperature or in standing water. Use one of the following approved methods: - Under potable running water of sufficient velocity to wash away loose food particles using water no greater than 70°F for no more than 2 hours. - In a refrigeration unit at 41°F or below - In a microwave - As part of the cooking process
114185.2All clean and soiled linen shall be properly stored; non-food items shall be stored and displayed separate from food and food-contact surfaces. Utensils and equipment shall be handled and stored so as to be protected from contamination., 114002, 114002.1 - Rapidly cool potentially hazardous foods from 135°F to 70°F within 2 hours, then from 70°F to 41°F within 4 hours. Discontinue cooling PHF's at room temperature. Rapid cool by any of the following approved methods: 1) Ice water bath 2) Ice wand 3) Shallow stainless steel pans filled 2-3 inches and store in refrigerator 4) Separate into smaller or thinner portions and store in refrigerator 5) Blast chiller 6) Any combination of the above. Use the following approved methods provided on the rapid cooling guideline., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 113984(d), 114097, 114099.1, 114099.4, 114099.6, 114101(b, c, d), 114105, 114109, 114111, 114113, 11415 (a, b, D), 114117, 114125(b), 114141 - Properly wash, rinse and sanitize all food contact surfaces. Make a 100 ppm bleach sanitizing solution or a 200 ppm quaternary ammonia solution for the third compartment., 114067(h), 114123, 114143(a, b), 114256-114256.2, 114256.4, 114257-114257.1, 114259, 114259.2-114259.3, 114279, 114281, 114282 - Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 114018, 114020 - Discontinue thawing potentially hazardous foods at room temperature or in standing water. Use one of the following approved methods: - Under potable running water of sufficient velocity to wash away loose food particles using water no greater than 70°F for no more than 2 hours. - In a refrigeration unit at 41°F or below - In a microwave - As part of the cooking process
114185.3All clean and soiled linen shall be properly stored; non-food items shall be stored and displayed separate from food and food-contact surfaces. Utensils and equipment shall be handled and stored so as to be protected from contamination., 114002, 114002.1 - Rapidly cool potentially hazardous foods from 135°F to 70°F within 2 hours, then from 70°F to 41°F within 4 hours. Discontinue cooling PHF's at room temperature. Rapid cool by any of the following approved methods: 1) Ice water bath 2) Ice wand 3) Shallow stainless steel pans filled 2-3 inches and store in refrigerator 4) Separate into smaller or thinner portions and store in refrigerator 5) Blast chiller 6) Any combination of the above. Use the following approved methods provided on the rapid cooling guideline., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 113984(d), 114097, 114099.1, 114099.4, 114099.6, 114101(b, c, d), 114105, 114109, 114111, 114113, 11415 (a, b, D), 114117, 114125(b), 114141 - Properly wash, rinse and sanitize all food contact surfaces. Make a 100 ppm bleach sanitizing solution or a 200 ppm quaternary ammonia solution for the third compartment., 114067(h), 114123, 114143(a, b), 114256-114256.2, 114256.4, 114257-114257.1, 114259, 114259.2-114259.3, 114279, 114281, 114282 - Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 114018, 114020 - Discontinue thawing potentially hazardous foods at room temperature or in standing water. Use one of the following approved methods: - Under potable running water of sufficient velocity to wash away loose food particles using water no greater than 70°F for no more than 2 hours. - In a refrigeration unit at 41°F or below - In a microwave - As part of the cooking process
114185.4All clean and soiled linen shall be properly stored; non-food items shall be stored and displayed separate from food and food-contact surfaces. Utensils and equipment shall be handled and stored so as to be protected from contamination., 114002, 114002.1 - Rapidly cool potentially hazardous foods from 135°F to 70°F within 2 hours, then from 70°F to 41°F within 4 hours. Discontinue cooling PHF's at room temperature. Rapid cool by any of the following approved methods: 1) Ice water bath 2) Ice wand 3) Shallow stainless steel pans filled 2-3 inches and store in refrigerator 4) Separate into smaller or thinner portions and store in refrigerator 5) Blast chiller 6) Any combination of the above. Use the following approved methods provided on the rapid cooling guideline., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 113984(d), 114097, 114099.1, 114099.4, 114099.6, 114101(b, c, d), 114105, 114109, 114111, 114113, 11415 (a, b, D), 114117, 114125(b), 114141 - Properly wash, rinse and sanitize all food contact surfaces. Make a 100 ppm bleach sanitizing solution or a 200 ppm quaternary ammonia solution for the third compartment., 114067(h), 114123, 114143(a, b), 114256-114256.2, 114256.4, 114257-114257.1, 114259, 114259.2-114259.3, 114279, 114281, 114282 - Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 114018, 114020 - Discontinue thawing potentially hazardous foods at room temperature or in standing water. Use one of the following approved methods: - Under potable running water of sufficient velocity to wash away loose food particles using water no greater than 70°F for no more than 2 hours. - In a refrigeration unit at 41°F or below - In a microwave - As part of the cooking process
114185.5All clean and soiled linen shall be properly stored; non-food items shall be stored and displayed separate from food and food-contact surfaces. Utensils and equipment shall be handled and stored so as to be protected from contamination., 114002, 114002.1 - Rapidly cool potentially hazardous foods from 135°F to 70°F within 2 hours, then from 70°F to 41°F within 4 hours. Discontinue cooling PHF's at room temperature. Rapid cool by any of the following approved methods: 1) Ice water bath 2) Ice wand 3) Shallow stainless steel pans filled 2-3 inches and store in refrigerator 4) Separate into smaller or thinner portions and store in refrigerator 5) Blast chiller 6) Any combination of the above. Use the following approved methods provided on the rapid cooling guideline., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 113984(d), 114097, 114099.1, 114099.4, 114099.6, 114101(b, c, d), 114105, 114109, 114111, 114113, 11415 (a, b, D), 114117, 114125(b), 114141 - Properly wash, rinse and sanitize all food contact surfaces. Make a 100 ppm bleach sanitizing solution or a 200 ppm quaternary ammonia solution for the third compartment., 114067(h), 114123, 114143(a, b), 114256-114256.2, 114256.4, 114257-114257.1, 114259, 114259.2-114259.3, 114279, 114281, 114282 - Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 114018, 114020 - Discontinue thawing potentially hazardous foods at room temperature or in standing water. Use one of the following approved methods: - Under potable running water of sufficient velocity to wash away loose food particles using water no greater than 70°F for no more than 2 hours. - In a refrigeration unit at 41°F or below - In a microwave - As part of the cooking process
September 25, 2025
Pass
P
114067(h)Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 114143(d), 114266, 114268, 114268.1, 114271, 114272 - Provide walls / ceilings using materials that are durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable, and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair.
114123Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 114143(d), 114266, 114268, 114268.1, 114271, 114272 - Provide walls / ceilings using materials that are durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable, and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair.
114143(aKeep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 114143(d), 114266, 114268, 114268.1, 114271, 114272 - Provide walls / ceilings using materials that are durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable, and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair.
114256-114256.2Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 114143(d), 114266, 114268, 114268.1, 114271, 114272 - Provide walls / ceilings using materials that are durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable, and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair.
114256.4Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 114143(d), 114266, 114268, 114268.1, 114271, 114272 - Provide walls / ceilings using materials that are durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable, and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair.
114257-114257.1Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 114143(d), 114266, 114268, 114268.1, 114271, 114272 - Provide walls / ceilings using materials that are durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable, and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair.
114259Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 114143(d), 114266, 114268, 114268.1, 114271, 114272 - Provide walls / ceilings using materials that are durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable, and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair.
114259.2-114259.3Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 114143(d), 114266, 114268, 114268.1, 114271, 114272 - Provide walls / ceilings using materials that are durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable, and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair.
114279Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 114143(d), 114266, 114268, 114268.1, 114271, 114272 - Provide walls / ceilings using materials that are durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable, and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair.
114281Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 114143(d), 114266, 114268, 114268.1, 114271, 114272 - Provide walls / ceilings using materials that are durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable, and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair.
114282Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 114143(d), 114266, 114268, 114268.1, 114271, 114272 - Provide walls / ceilings using materials that are durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable, and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair.
September 25, 2025
Pass
P
114067(h)Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 114143(d), 114266, 114268, 114268.1, 114271, 114272 - Provide walls / ceilings using materials that are durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable, and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair.
114123Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 114143(d), 114266, 114268, 114268.1, 114271, 114272 - Provide walls / ceilings using materials that are durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable, and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair.
114143(aKeep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 114143(d), 114266, 114268, 114268.1, 114271, 114272 - Provide walls / ceilings using materials that are durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable, and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair.
114256-114256.2Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 114143(d), 114266, 114268, 114268.1, 114271, 114272 - Provide walls / ceilings using materials that are durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable, and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair.
114256.4Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 114143(d), 114266, 114268, 114268.1, 114271, 114272 - Provide walls / ceilings using materials that are durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable, and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair.
114257-114257.1Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 114143(d), 114266, 114268, 114268.1, 114271, 114272 - Provide walls / ceilings using materials that are durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable, and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair.
114259Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 114143(d), 114266, 114268, 114268.1, 114271, 114272 - Provide walls / ceilings using materials that are durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable, and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair.
114259.2-114259.3Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 114143(d), 114266, 114268, 114268.1, 114271, 114272 - Provide walls / ceilings using materials that are durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable, and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair.
114279Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 114143(d), 114266, 114268, 114268.1, 114271, 114272 - Provide walls / ceilings using materials that are durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable, and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair.
114281Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 114143(d), 114266, 114268, 114268.1, 114271, 114272 - Provide walls / ceilings using materials that are durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable, and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair.
114282Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 1114149-114149.3, 114252, 114252.1 - Provide exhaust hoods to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6 inches beyond all cooking equipment. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields., 114143(d), 114266, 114268, 114268.1, 114271, 114272 - Provide walls / ceilings using materials that are durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable, and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair.
May 30, 2025
Site Visit
Pass
P
December 19, 2024
Pass
P
December 19, 2024
Pass
P
December 17, 2024
Pass
P
114268Floor surfaces shall be coved at the juncture of the floor and wall with a 3/8 inch minimum radius coving and shall extend up the wall at least 4 inches., 114163 - All permanent food facilities that wash, rinse, soak, thaw, or similarly prepare foods shall be provided with a food preparation sink with a single integral drainboard. The food preparation sink shall have a minimum dimension of 18"x18"x12" (LxWxD) with an integral drainboard at least 18"x18" (LxW)., 113953, 113953(b) - Hand sinks shall be sufficient in number and conveniently located so as to be accessible at all times., 114271 - Wall and ceiling finish shall be smooth, durable, easily cleanable, and non-absorbent in all areas where there is food service or preparation, open food storage, warewashing, janitorial service, trash storage, and employee restrooms., 114153 - Equipment for cooling, e.g. ice machine, walk-in cooler/freezer, shall be sufficient in number and capacity to ensure proper food temperature control., 114268 - The floor finish shall be smooth, durable, easily cleanable, and non-absorbent in all areas where there is food service or preparation, open food storage, warewashing, janitorial service, trash storage, and employee restrooms.
December 17, 2024
Pass
P
114268Floor surfaces shall be coved at the juncture of the floor and wall with a 3/8 inch minimum radius coving and shall extend up the wall at least 4 inches., 114163 - All permanent food facilities that wash, rinse, soak, thaw, or similarly prepare foods shall be provided with a food preparation sink with a single integral drainboard. The food preparation sink shall have a minimum dimension of 18"x18"x12" (LxWxD) with an integral drainboard at least 18"x18" (LxW)., 113953, 113953(b) - Hand sinks shall be sufficient in number and conveniently located so as to be accessible at all times., 114271 - Wall and ceiling finish shall be smooth, durable, easily cleanable, and non-absorbent in all areas where there is food service or preparation, open food storage, warewashing, janitorial service, trash storage, and employee restrooms., 114153 - Equipment for cooling, e.g. ice machine, walk-in cooler/freezer, shall be sufficient in number and capacity to ensure proper food temperature control., 114268 - The floor finish shall be smooth, durable, easily cleanable, and non-absorbent in all areas where there is food service or preparation, open food storage, warewashing, janitorial service, trash storage, and employee restrooms.
December 3, 2024
Reinspection
Pass
P
114130-114130.5Ensure all equipment is approved, properly installed, clean, and maintained in good repair. Ensure all appliances are NSF-approved, commercial grade, durable, and easily cleanable.
114132Ensure all equipment is approved, properly installed, clean, and maintained in good repair. Ensure all appliances are NSF-approved, commercial grade, durable, and easily cleanable.
114133Ensure all equipment is approved, properly installed, clean, and maintained in good repair. Ensure all appliances are NSF-approved, commercial grade, durable, and easily cleanable.
114137Ensure all equipment is approved, properly installed, clean, and maintained in good repair. Ensure all appliances are NSF-approved, commercial grade, durable, and easily cleanable.
114139Ensure all equipment is approved, properly installed, clean, and maintained in good repair. Ensure all appliances are NSF-approved, commercial grade, durable, and easily cleanable.
114153Ensure all equipment is approved, properly installed, clean, and maintained in good repair. Ensure all appliances are NSF-approved, commercial grade, durable, and easily cleanable.
114163Ensure all equipment is approved, properly installed, clean, and maintained in good repair. Ensure all appliances are NSF-approved, commercial grade, durable, and easily cleanable.
114165Ensure all equipment is approved, properly installed, clean, and maintained in good repair. Ensure all appliances are NSF-approved, commercial grade, durable, and easily cleanable.
114167Ensure all equipment is approved, properly installed, clean, and maintained in good repair. Ensure all appliances are NSF-approved, commercial grade, durable, and easily cleanable.
114169Ensure all equipment is approved, properly installed, clean, and maintained in good repair. Ensure all appliances are NSF-approved, commercial grade, durable, and easily cleanable.
114175Ensure all equipment is approved, properly installed, clean, and maintained in good repair. Ensure all appliances are NSF-approved, commercial grade, durable, and easily cleanable.
114177Ensure all equipment is approved, properly installed, clean, and maintained in good repair. Ensure all appliances are NSF-approved, commercial grade, durable, and easily cleanable.
114180Ensure all equipment is approved, properly installed, clean, and maintained in good repair. Ensure all appliances are NSF-approved, commercial grade, durable, and easily cleanable.
114182Ensure all equipment is approved, properly installed, clean, and maintained in good repair. Ensure all appliances are NSF-approved, commercial grade, durable, and easily cleanable.
November 19, 2024
Routine
Pass
P
114259Eliminate the infestation/activity of cockroaches/rodents/flies/vermin from the food facility by using only approved methods. Remove all evidence of the infestation and thoroughly clean and sanitize all affected surfaces. Construct, equip, maintain and operate the food facility so as to prevent the entrance and harborage of animals, birds and vermin including, but not limited to, rodents and insects., 113984(d), 114097, 114099.1, 114099.4, 114099.6, 114101(b, c, d), 114105, 114109, 114111, 114113, 11415 (a, b, D), 114117, 114125(b), 114141 - Properly wash, rinse and sanitize all food contact surfaces. Make a 100 ppm bleach sanitizing solution or a 200 ppm quaternary ammonia solution for the third compartment., 114130-114130.5, 114132, 114133, 114137, 114139, 114153, 114163, 114165, 114167, 114169, 114175, 114177, 114180, 114182 - Ensure all equipment is approved, properly installed, clean, and maintained in good repair. Ensure all appliances are NSF-approved, commercial grade, durable, and easily cleanable., 113953, 113953.1, 113953.2, 114067(f) - Provide soap and single-use towels in dispensers, or a drying device at each handwash sink at all times. Maintain all handwash sinks unobstructed and accessible at all times.
114259.1Eliminate the infestation/activity of cockroaches/rodents/flies/vermin from the food facility by using only approved methods. Remove all evidence of the infestation and thoroughly clean and sanitize all affected surfaces. Construct, equip, maintain and operate the food facility so as to prevent the entrance and harborage of animals, birds and vermin including, but not limited to, rodents and insects., 113984(d), 114097, 114099.1, 114099.4, 114099.6, 114101(b, c, d), 114105, 114109, 114111, 114113, 11415 (a, b, D), 114117, 114125(b), 114141 - Properly wash, rinse and sanitize all food contact surfaces. Make a 100 ppm bleach sanitizing solution or a 200 ppm quaternary ammonia solution for the third compartment., 114130-114130.5, 114132, 114133, 114137, 114139, 114153, 114163, 114165, 114167, 114169, 114175, 114177, 114180, 114182 - Ensure all equipment is approved, properly installed, clean, and maintained in good repair. Ensure all appliances are NSF-approved, commercial grade, durable, and easily cleanable., 113953, 113953.1, 113953.2, 114067(f) - Provide soap and single-use towels in dispensers, or a drying device at each handwash sink at all times. Maintain all handwash sinks unobstructed and accessible at all times.
114259.4Eliminate the infestation/activity of cockroaches/rodents/flies/vermin from the food facility by using only approved methods. Remove all evidence of the infestation and thoroughly clean and sanitize all affected surfaces. Construct, equip, maintain and operate the food facility so as to prevent the entrance and harborage of animals, birds and vermin including, but not limited to, rodents and insects., 113984(d), 114097, 114099.1, 114099.4, 114099.6, 114101(b, c, d), 114105, 114109, 114111, 114113, 11415 (a, b, D), 114117, 114125(b), 114141 - Properly wash, rinse and sanitize all food contact surfaces. Make a 100 ppm bleach sanitizing solution or a 200 ppm quaternary ammonia solution for the third compartment., 114130-114130.5, 114132, 114133, 114137, 114139, 114153, 114163, 114165, 114167, 114169, 114175, 114177, 114180, 114182 - Ensure all equipment is approved, properly installed, clean, and maintained in good repair. Ensure all appliances are NSF-approved, commercial grade, durable, and easily cleanable., 113953, 113953.1, 113953.2, 114067(f) - Provide soap and single-use towels in dispensers, or a drying device at each handwash sink at all times. Maintain all handwash sinks unobstructed and accessible at all times.
114259.5Eliminate the infestation/activity of cockroaches/rodents/flies/vermin from the food facility by using only approved methods. Remove all evidence of the infestation and thoroughly clean and sanitize all affected surfaces. Construct, equip, maintain and operate the food facility so as to prevent the entrance and harborage of animals, birds and vermin including, but not limited to, rodents and insects., 113984(d), 114097, 114099.1, 114099.4, 114099.6, 114101(b, c, d), 114105, 114109, 114111, 114113, 11415 (a, b, D), 114117, 114125(b), 114141 - Properly wash, rinse and sanitize all food contact surfaces. Make a 100 ppm bleach sanitizing solution or a 200 ppm quaternary ammonia solution for the third compartment., 114130-114130.5, 114132, 114133, 114137, 114139, 114153, 114163, 114165, 114167, 114169, 114175, 114177, 114180, 114182 - Ensure all equipment is approved, properly installed, clean, and maintained in good repair. Ensure all appliances are NSF-approved, commercial grade, durable, and easily cleanable., 113953, 113953.1, 113953.2, 114067(f) - Provide soap and single-use towels in dispensers, or a drying device at each handwash sink at all times. Maintain all handwash sinks unobstructed and accessible at all times.
July 2, 2024
New Ownership (R)
Pass
P
June 18, 2024
New Ownership (I)
Pass
P