Tbd
49 S Van Ness Ave 7Th Floor
P
Last inspected: July 9, 2024
Inspection History
July 9, 2024
Pass
P
114257A food facility shall at all times be constructed, equipped, and maintained, and operated as to prevent the entrance and harborage of animals, birds, and vermin, including, but not limited to rodents and insects., 114163 - All permanent food facilities that wash, rinse, soak, thaw, or similarly prepare foods shall be provided with a food preparation sink with a single integral drainboard. The food preparation sink shall have a minimum dimension of 18"x18"x12" (LxWxD) with an integral drainboard at least 18"x18" (LxW)., 114192, 113953 - Pressurized warm water shall be provided by all handwashing sinks for a minimum of 15 seconds through a mixing valve or combination faucet. At handwashing sinks where the water temperature provided is not readily adjustable at the faucets, warm water between 100°F-108°F shall be provided., 114192, 113953 - The water supply shall be from a water system approved by the local enforcement agency. , 114193, 114193.1, 114269 - Equipment that discharges liquid waste, e.g. food preparation sinks, dishwashing machines, steam tables, ice machines and bins, espresso machines, walk-in refrigeration units, shall have approved indirect drainage through an air gap into a floor sink or other approved receiving vessel., 114130, 114169 - All new and used equipment and utensils shall be certified or classified for sanitation by an American National Standards Institute (ANSI) accredited certification program, e.g. NSF, ETL Sanitation, UL Sanitation, CSA Sanitation. , 113953, 113953(b) - Hand sinks shall be sufficient in number and conveniently located so as to be accessible at all times., 114130, 114169 - All equipment shall be installed on castors, six (6) inch high round metal legs, or on a minimum four (4) inch high curb or pedestal with a continuously coved base at the juncture., 114268 - Floor surfaces shall be coved at the juncture of the floor and wall with a 3/8 inch minimum radius coving and shall extend up the wall at least 4 inches., 114268 - The floor finish shall be smooth, durable, easily cleanable, and non-absorbent in all areas where there is food service or preparation, open food storage, warewashing, janitorial service, trash storage, and employee restrooms., 114256 - Lockers or other suitable facilities shall be located in a designated room or area where contamination of food, equipment, utensils, linens, and single-use articles cannot occur., 114276, 114149, SF Health Code Section 440.5 - Toilet facilities that are provided for use by consumers, guests, or invitees shall be in a location where consumers, guests, and invitees do not pass through food preparation, food storage, or utensil washing areas to reach the toilet facilities., 114271 - Wall and ceiling finish shall be smooth, durable, easily cleanable, and non-absorbent in all areas where there is food service or preparation, open food storage, warewashing, janitorial service, trash storage, and employee restrooms., 114279, 114281, 114282 - At least one curbed cleaning facility or janitorial sink equipped with hot and cold water and a drain shall be provided and conveniently located.
114257.1A food facility shall at all times be constructed, equipped, and maintained, and operated as to prevent the entrance and harborage of animals, birds, and vermin, including, but not limited to rodents and insects., 114163 - All permanent food facilities that wash, rinse, soak, thaw, or similarly prepare foods shall be provided with a food preparation sink with a single integral drainboard. The food preparation sink shall have a minimum dimension of 18"x18"x12" (LxWxD) with an integral drainboard at least 18"x18" (LxW)., 114192, 113953 - Pressurized warm water shall be provided by all handwashing sinks for a minimum of 15 seconds through a mixing valve or combination faucet. At handwashing sinks where the water temperature provided is not readily adjustable at the faucets, warm water between 100°F-108°F shall be provided., 114192, 113953 - The water supply shall be from a water system approved by the local enforcement agency. , 114193, 114193.1, 114269 - Equipment that discharges liquid waste, e.g. food preparation sinks, dishwashing machines, steam tables, ice machines and bins, espresso machines, walk-in refrigeration units, shall have approved indirect drainage through an air gap into a floor sink or other approved receiving vessel., 114130, 114169 - All new and used equipment and utensils shall be certified or classified for sanitation by an American National Standards Institute (ANSI) accredited certification program, e.g. NSF, ETL Sanitation, UL Sanitation, CSA Sanitation. , 113953, 113953(b) - Hand sinks shall be sufficient in number and conveniently located so as to be accessible at all times., 114130, 114169 - All equipment shall be installed on castors, six (6) inch high round metal legs, or on a minimum four (4) inch high curb or pedestal with a continuously coved base at the juncture., 114268 - Floor surfaces shall be coved at the juncture of the floor and wall with a 3/8 inch minimum radius coving and shall extend up the wall at least 4 inches., 114268 - The floor finish shall be smooth, durable, easily cleanable, and non-absorbent in all areas where there is food service or preparation, open food storage, warewashing, janitorial service, trash storage, and employee restrooms., 114256 - Lockers or other suitable facilities shall be located in a designated room or area where contamination of food, equipment, utensils, linens, and single-use articles cannot occur., 114276, 114149, SF Health Code Section 440.5 - Toilet facilities that are provided for use by consumers, guests, or invitees shall be in a location where consumers, guests, and invitees do not pass through food preparation, food storage, or utensil washing areas to reach the toilet facilities., 114271 - Wall and ceiling finish shall be smooth, durable, easily cleanable, and non-absorbent in all areas where there is food service or preparation, open food storage, warewashing, janitorial service, trash storage, and employee restrooms., 114279, 114281, 114282 - At least one curbed cleaning facility or janitorial sink equipped with hot and cold water and a drain shall be provided and conveniently located.
114259A food facility shall at all times be constructed, equipped, and maintained, and operated as to prevent the entrance and harborage of animals, birds, and vermin, including, but not limited to rodents and insects., 114163 - All permanent food facilities that wash, rinse, soak, thaw, or similarly prepare foods shall be provided with a food preparation sink with a single integral drainboard. The food preparation sink shall have a minimum dimension of 18"x18"x12" (LxWxD) with an integral drainboard at least 18"x18" (LxW)., 114192, 113953 - Pressurized warm water shall be provided by all handwashing sinks for a minimum of 15 seconds through a mixing valve or combination faucet. At handwashing sinks where the water temperature provided is not readily adjustable at the faucets, warm water between 100°F-108°F shall be provided., 114192, 113953 - The water supply shall be from a water system approved by the local enforcement agency. , 114193, 114193.1, 114269 - Equipment that discharges liquid waste, e.g. food preparation sinks, dishwashing machines, steam tables, ice machines and bins, espresso machines, walk-in refrigeration units, shall have approved indirect drainage through an air gap into a floor sink or other approved receiving vessel., 114130, 114169 - All new and used equipment and utensils shall be certified or classified for sanitation by an American National Standards Institute (ANSI) accredited certification program, e.g. NSF, ETL Sanitation, UL Sanitation, CSA Sanitation. , 113953, 113953(b) - Hand sinks shall be sufficient in number and conveniently located so as to be accessible at all times., 114130, 114169 - All equipment shall be installed on castors, six (6) inch high round metal legs, or on a minimum four (4) inch high curb or pedestal with a continuously coved base at the juncture., 114268 - Floor surfaces shall be coved at the juncture of the floor and wall with a 3/8 inch minimum radius coving and shall extend up the wall at least 4 inches., 114268 - The floor finish shall be smooth, durable, easily cleanable, and non-absorbent in all areas where there is food service or preparation, open food storage, warewashing, janitorial service, trash storage, and employee restrooms., 114256 - Lockers or other suitable facilities shall be located in a designated room or area where contamination of food, equipment, utensils, linens, and single-use articles cannot occur., 114276, 114149, SF Health Code Section 440.5 - Toilet facilities that are provided for use by consumers, guests, or invitees shall be in a location where consumers, guests, and invitees do not pass through food preparation, food storage, or utensil washing areas to reach the toilet facilities., 114271 - Wall and ceiling finish shall be smooth, durable, easily cleanable, and non-absorbent in all areas where there is food service or preparation, open food storage, warewashing, janitorial service, trash storage, and employee restrooms., 114279, 114281, 114282 - At least one curbed cleaning facility or janitorial sink equipped with hot and cold water and a drain shall be provided and conveniently located.
114266A food facility shall at all times be constructed, equipped, and maintained, and operated as to prevent the entrance and harborage of animals, birds, and vermin, including, but not limited to rodents and insects., 114163 - All permanent food facilities that wash, rinse, soak, thaw, or similarly prepare foods shall be provided with a food preparation sink with a single integral drainboard. The food preparation sink shall have a minimum dimension of 18"x18"x12" (LxWxD) with an integral drainboard at least 18"x18" (LxW)., 114192, 113953 - Pressurized warm water shall be provided by all handwashing sinks for a minimum of 15 seconds through a mixing valve or combination faucet. At handwashing sinks where the water temperature provided is not readily adjustable at the faucets, warm water between 100°F-108°F shall be provided., 114192, 113953 - The water supply shall be from a water system approved by the local enforcement agency. , 114193, 114193.1, 114269 - Equipment that discharges liquid waste, e.g. food preparation sinks, dishwashing machines, steam tables, ice machines and bins, espresso machines, walk-in refrigeration units, shall have approved indirect drainage through an air gap into a floor sink or other approved receiving vessel., 114130, 114169 - All new and used equipment and utensils shall be certified or classified for sanitation by an American National Standards Institute (ANSI) accredited certification program, e.g. NSF, ETL Sanitation, UL Sanitation, CSA Sanitation. , 113953, 113953(b) - Hand sinks shall be sufficient in number and conveniently located so as to be accessible at all times., 114130, 114169 - All equipment shall be installed on castors, six (6) inch high round metal legs, or on a minimum four (4) inch high curb or pedestal with a continuously coved base at the juncture., 114268 - Floor surfaces shall be coved at the juncture of the floor and wall with a 3/8 inch minimum radius coving and shall extend up the wall at least 4 inches., 114268 - The floor finish shall be smooth, durable, easily cleanable, and non-absorbent in all areas where there is food service or preparation, open food storage, warewashing, janitorial service, trash storage, and employee restrooms., 114256 - Lockers or other suitable facilities shall be located in a designated room or area where contamination of food, equipment, utensils, linens, and single-use articles cannot occur., 114276, 114149, SF Health Code Section 440.5 - Toilet facilities that are provided for use by consumers, guests, or invitees shall be in a location where consumers, guests, and invitees do not pass through food preparation, food storage, or utensil washing areas to reach the toilet facilities., 114271 - Wall and ceiling finish shall be smooth, durable, easily cleanable, and non-absorbent in all areas where there is food service or preparation, open food storage, warewashing, janitorial service, trash storage, and employee restrooms., 114279, 114281, 114282 - At least one curbed cleaning facility or janitorial sink equipped with hot and cold water and a drain shall be provided and conveniently located.
July 9, 2024
Pass
P
114257A food facility shall at all times be constructed, equipped, and maintained, and operated as to prevent the entrance and harborage of animals, birds, and vermin, including, but not limited to rodents and insects., 114163 - All permanent food facilities that wash, rinse, soak, thaw, or similarly prepare foods shall be provided with a food preparation sink with a single integral drainboard. The food preparation sink shall have a minimum dimension of 18"x18"x12" (LxWxD) with an integral drainboard at least 18"x18" (LxW)., 114192, 113953 - Pressurized warm water shall be provided by all handwashing sinks for a minimum of 15 seconds through a mixing valve or combination faucet. At handwashing sinks where the water temperature provided is not readily adjustable at the faucets, warm water between 100°F-108°F shall be provided., 114192, 113953 - The water supply shall be from a water system approved by the local enforcement agency. , 114193, 114193.1, 114269 - Equipment that discharges liquid waste, e.g. food preparation sinks, dishwashing machines, steam tables, ice machines and bins, espresso machines, walk-in refrigeration units, shall have approved indirect drainage through an air gap into a floor sink or other approved receiving vessel., 114130, 114169 - All new and used equipment and utensils shall be certified or classified for sanitation by an American National Standards Institute (ANSI) accredited certification program, e.g. NSF, ETL Sanitation, UL Sanitation, CSA Sanitation. , 113953, 113953(b) - Hand sinks shall be sufficient in number and conveniently located so as to be accessible at all times., 114130, 114169 - All equipment shall be installed on castors, six (6) inch high round metal legs, or on a minimum four (4) inch high curb or pedestal with a continuously coved base at the juncture., 114268 - Floor surfaces shall be coved at the juncture of the floor and wall with a 3/8 inch minimum radius coving and shall extend up the wall at least 4 inches., 114268 - The floor finish shall be smooth, durable, easily cleanable, and non-absorbent in all areas where there is food service or preparation, open food storage, warewashing, janitorial service, trash storage, and employee restrooms., 114256 - Lockers or other suitable facilities shall be located in a designated room or area where contamination of food, equipment, utensils, linens, and single-use articles cannot occur., 114276, 114149, SF Health Code Section 440.5 - Toilet facilities that are provided for use by consumers, guests, or invitees shall be in a location where consumers, guests, and invitees do not pass through food preparation, food storage, or utensil washing areas to reach the toilet facilities., 114271 - Wall and ceiling finish shall be smooth, durable, easily cleanable, and non-absorbent in all areas where there is food service or preparation, open food storage, warewashing, janitorial service, trash storage, and employee restrooms., 114279, 114281, 114282 - At least one curbed cleaning facility or janitorial sink equipped with hot and cold water and a drain shall be provided and conveniently located.
114257.1A food facility shall at all times be constructed, equipped, and maintained, and operated as to prevent the entrance and harborage of animals, birds, and vermin, including, but not limited to rodents and insects., 114163 - All permanent food facilities that wash, rinse, soak, thaw, or similarly prepare foods shall be provided with a food preparation sink with a single integral drainboard. The food preparation sink shall have a minimum dimension of 18"x18"x12" (LxWxD) with an integral drainboard at least 18"x18" (LxW)., 114192, 113953 - Pressurized warm water shall be provided by all handwashing sinks for a minimum of 15 seconds through a mixing valve or combination faucet. At handwashing sinks where the water temperature provided is not readily adjustable at the faucets, warm water between 100°F-108°F shall be provided., 114192, 113953 - The water supply shall be from a water system approved by the local enforcement agency. , 114193, 114193.1, 114269 - Equipment that discharges liquid waste, e.g. food preparation sinks, dishwashing machines, steam tables, ice machines and bins, espresso machines, walk-in refrigeration units, shall have approved indirect drainage through an air gap into a floor sink or other approved receiving vessel., 114130, 114169 - All new and used equipment and utensils shall be certified or classified for sanitation by an American National Standards Institute (ANSI) accredited certification program, e.g. NSF, ETL Sanitation, UL Sanitation, CSA Sanitation. , 113953, 113953(b) - Hand sinks shall be sufficient in number and conveniently located so as to be accessible at all times., 114130, 114169 - All equipment shall be installed on castors, six (6) inch high round metal legs, or on a minimum four (4) inch high curb or pedestal with a continuously coved base at the juncture., 114268 - Floor surfaces shall be coved at the juncture of the floor and wall with a 3/8 inch minimum radius coving and shall extend up the wall at least 4 inches., 114268 - The floor finish shall be smooth, durable, easily cleanable, and non-absorbent in all areas where there is food service or preparation, open food storage, warewashing, janitorial service, trash storage, and employee restrooms., 114256 - Lockers or other suitable facilities shall be located in a designated room or area where contamination of food, equipment, utensils, linens, and single-use articles cannot occur., 114276, 114149, SF Health Code Section 440.5 - Toilet facilities that are provided for use by consumers, guests, or invitees shall be in a location where consumers, guests, and invitees do not pass through food preparation, food storage, or utensil washing areas to reach the toilet facilities., 114271 - Wall and ceiling finish shall be smooth, durable, easily cleanable, and non-absorbent in all areas where there is food service or preparation, open food storage, warewashing, janitorial service, trash storage, and employee restrooms., 114279, 114281, 114282 - At least one curbed cleaning facility or janitorial sink equipped with hot and cold water and a drain shall be provided and conveniently located.
114259A food facility shall at all times be constructed, equipped, and maintained, and operated as to prevent the entrance and harborage of animals, birds, and vermin, including, but not limited to rodents and insects., 114163 - All permanent food facilities that wash, rinse, soak, thaw, or similarly prepare foods shall be provided with a food preparation sink with a single integral drainboard. The food preparation sink shall have a minimum dimension of 18"x18"x12" (LxWxD) with an integral drainboard at least 18"x18" (LxW)., 114192, 113953 - Pressurized warm water shall be provided by all handwashing sinks for a minimum of 15 seconds through a mixing valve or combination faucet. At handwashing sinks where the water temperature provided is not readily adjustable at the faucets, warm water between 100°F-108°F shall be provided., 114192, 113953 - The water supply shall be from a water system approved by the local enforcement agency. , 114193, 114193.1, 114269 - Equipment that discharges liquid waste, e.g. food preparation sinks, dishwashing machines, steam tables, ice machines and bins, espresso machines, walk-in refrigeration units, shall have approved indirect drainage through an air gap into a floor sink or other approved receiving vessel., 114130, 114169 - All new and used equipment and utensils shall be certified or classified for sanitation by an American National Standards Institute (ANSI) accredited certification program, e.g. NSF, ETL Sanitation, UL Sanitation, CSA Sanitation. , 113953, 113953(b) - Hand sinks shall be sufficient in number and conveniently located so as to be accessible at all times., 114130, 114169 - All equipment shall be installed on castors, six (6) inch high round metal legs, or on a minimum four (4) inch high curb or pedestal with a continuously coved base at the juncture., 114268 - Floor surfaces shall be coved at the juncture of the floor and wall with a 3/8 inch minimum radius coving and shall extend up the wall at least 4 inches., 114268 - The floor finish shall be smooth, durable, easily cleanable, and non-absorbent in all areas where there is food service or preparation, open food storage, warewashing, janitorial service, trash storage, and employee restrooms., 114256 - Lockers or other suitable facilities shall be located in a designated room or area where contamination of food, equipment, utensils, linens, and single-use articles cannot occur., 114276, 114149, SF Health Code Section 440.5 - Toilet facilities that are provided for use by consumers, guests, or invitees shall be in a location where consumers, guests, and invitees do not pass through food preparation, food storage, or utensil washing areas to reach the toilet facilities., 114271 - Wall and ceiling finish shall be smooth, durable, easily cleanable, and non-absorbent in all areas where there is food service or preparation, open food storage, warewashing, janitorial service, trash storage, and employee restrooms., 114279, 114281, 114282 - At least one curbed cleaning facility or janitorial sink equipped with hot and cold water and a drain shall be provided and conveniently located.
114266A food facility shall at all times be constructed, equipped, and maintained, and operated as to prevent the entrance and harborage of animals, birds, and vermin, including, but not limited to rodents and insects., 114163 - All permanent food facilities that wash, rinse, soak, thaw, or similarly prepare foods shall be provided with a food preparation sink with a single integral drainboard. The food preparation sink shall have a minimum dimension of 18"x18"x12" (LxWxD) with an integral drainboard at least 18"x18" (LxW)., 114192, 113953 - Pressurized warm water shall be provided by all handwashing sinks for a minimum of 15 seconds through a mixing valve or combination faucet. At handwashing sinks where the water temperature provided is not readily adjustable at the faucets, warm water between 100°F-108°F shall be provided., 114192, 113953 - The water supply shall be from a water system approved by the local enforcement agency. , 114193, 114193.1, 114269 - Equipment that discharges liquid waste, e.g. food preparation sinks, dishwashing machines, steam tables, ice machines and bins, espresso machines, walk-in refrigeration units, shall have approved indirect drainage through an air gap into a floor sink or other approved receiving vessel., 114130, 114169 - All new and used equipment and utensils shall be certified or classified for sanitation by an American National Standards Institute (ANSI) accredited certification program, e.g. NSF, ETL Sanitation, UL Sanitation, CSA Sanitation. , 113953, 113953(b) - Hand sinks shall be sufficient in number and conveniently located so as to be accessible at all times., 114130, 114169 - All equipment shall be installed on castors, six (6) inch high round metal legs, or on a minimum four (4) inch high curb or pedestal with a continuously coved base at the juncture., 114268 - Floor surfaces shall be coved at the juncture of the floor and wall with a 3/8 inch minimum radius coving and shall extend up the wall at least 4 inches., 114268 - The floor finish shall be smooth, durable, easily cleanable, and non-absorbent in all areas where there is food service or preparation, open food storage, warewashing, janitorial service, trash storage, and employee restrooms., 114256 - Lockers or other suitable facilities shall be located in a designated room or area where contamination of food, equipment, utensils, linens, and single-use articles cannot occur., 114276, 114149, SF Health Code Section 440.5 - Toilet facilities that are provided for use by consumers, guests, or invitees shall be in a location where consumers, guests, and invitees do not pass through food preparation, food storage, or utensil washing areas to reach the toilet facilities., 114271 - Wall and ceiling finish shall be smooth, durable, easily cleanable, and non-absorbent in all areas where there is food service or preparation, open food storage, warewashing, janitorial service, trash storage, and employee restrooms., 114279, 114281, 114282 - At least one curbed cleaning facility or janitorial sink equipped with hot and cold water and a drain shall be provided and conveniently located.