The Olympic Club (Lower Level)

December 19, 2025

Pass

P

114157Maintain onsite an accurate, easily readable metal probe thermometer suitable for measuring temperature of food shall be available. A display thermometer +/- 2F shall be provided for each hot and cold holding unit of potentially hazardous foods and high temperature warewashing machines., 113996, 113998, 114037, 114429, 114429.3, 114429.5 - Keep potentially hazardous foods (PHF) cold at 41°F or below or hot held at 135°F or above. Immediately discontinue storing PHF at room temperature., 113953, 113953.1, 113953.2, 114067(f) - Provide soap and single-use towels in dispensers, or a drying device at each handwash sink at all times. Maintain all handwash sinks unobstructed and accessible at all times., 114067(h), 114123, 114143(a, b), 114256-114256.2, 114256.4, 114257-114257.1, 114259, 114259.2-114259.3, 114279, 114281, 114282 - Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 113953(c), 114163(a)(3), 114189, 114192.1, 114195, 114279 - Immediately provide hot running potable water of at least 120°F or greater for the entire food preparation facility., 113984(d), 114097, 114099.1, 114099.4, 114099.6, 114101(b, c, d), 114105, 114109, 114111, 114113, 11415 (a, b, D), 114117, 114125(b), 114141 - Properly wash, rinse and sanitize all food contact surfaces. Make a 100 ppm bleach sanitizing solution or a 200 ppm quaternary ammonia solution for the third compartment., - Submit additional documents as instructed., 114002, 114002.1 - Rapidly cool potentially hazardous foods from 135°F to 70°F within 2 hours, then from 70°F to 41°F within 4 hours. Discontinue cooling PHF's at room temperature. Rapid cool by any of the following approved methods: 1) Ice water bath 2) Ice wand 3) Shallow stainless steel pans filled 2-3 inches and store in refrigerator 4) Separate into smaller or thinner portions and store in refrigerator 5) Blast chiller 6) Any combination of the above. Use the following approved methods provided on the rapid cooling guideline., 113952, 113953.3, 113953.4, 113961, 113973 - Properly wash hands with hand soap and warm water for a minimum of 10 seconds at the hand washing station when beginning work; before handling food/equipment/utensils; as often as necessary during food preparation to remove soil and contamination; switching from working with raw to ready-to-eat foods; after touching body parts; after using toilet room; contamination of hands occurs. Food employees shall minimize contact with exposed, ready-to-eat food with their bare hands and shall use suitable utensils, gloves, or dispensing equipment., 114047, 114049, 114051, 114053, 114055, 114069(b) - Elevate all food at least 6 inches off of the floor to prevent contamination. Properly label bulk ingredient/food containers with common name., 114135, 114185.1 114185.3 [d-e] - Store wiping cloths used to wipe service counters, scales, or other surfaces that may come into contact with food in clean water with sanitizer or use only once; separate sanitizing containers shall be provided for wiping cloths used with raw animal foods., 114074, 114081, 114119, 114121, 114161, 114178, 114179, 114083, 114185, 114185.2, 114185.3, 114185.4, 114185.5 - All clean and soiled linen shall be properly stored; non-food items shall be stored and displayed separate from food and food-contact surfaces. Utensils and equipment shall be handled and stored so as to be protected from contamination., 113947.1-113947.6, 113948 - Obtain a state approved food safety certification course within 60 days of operation or when a Food Safety Manager has left the facility. Maintain copies of food safety certificates (food safety manager and food handler cards) on site., 114171, 114189.1, 114190, 114192, 114193, 114193.1, 114199, 114201, 114269 - Protect the potable water supply with a backflow protection device, as required by applicable plumbing codes. All plumbing, plumbing fixtures, and grease interceptors shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Any hose used for conveying potable water shall be of approved materials, labeled, properly stored, and used for no other purpose., - Food, equipment, or utensils that are found to be unsanitary or in disrepair may be Voluntarily Condemned and Destroyed by the person in charge.

114159Maintain onsite an accurate, easily readable metal probe thermometer suitable for measuring temperature of food shall be available. A display thermometer +/- 2F shall be provided for each hot and cold holding unit of potentially hazardous foods and high temperature warewashing machines., 113996, 113998, 114037, 114429, 114429.3, 114429.5 - Keep potentially hazardous foods (PHF) cold at 41°F or below or hot held at 135°F or above. Immediately discontinue storing PHF at room temperature., 113953, 113953.1, 113953.2, 114067(f) - Provide soap and single-use towels in dispensers, or a drying device at each handwash sink at all times. Maintain all handwash sinks unobstructed and accessible at all times., 114067(h), 114123, 114143(a, b), 114256-114256.2, 114256.4, 114257-114257.1, 114259, 114259.2-114259.3, 114279, 114281, 114282 - Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 113953(c), 114163(a)(3), 114189, 114192.1, 114195, 114279 - Immediately provide hot running potable water of at least 120°F or greater for the entire food preparation facility., 113984(d), 114097, 114099.1, 114099.4, 114099.6, 114101(b, c, d), 114105, 114109, 114111, 114113, 11415 (a, b, D), 114117, 114125(b), 114141 - Properly wash, rinse and sanitize all food contact surfaces. Make a 100 ppm bleach sanitizing solution or a 200 ppm quaternary ammonia solution for the third compartment., - Submit additional documents as instructed., 114002, 114002.1 - Rapidly cool potentially hazardous foods from 135°F to 70°F within 2 hours, then from 70°F to 41°F within 4 hours. Discontinue cooling PHF's at room temperature. Rapid cool by any of the following approved methods: 1) Ice water bath 2) Ice wand 3) Shallow stainless steel pans filled 2-3 inches and store in refrigerator 4) Separate into smaller or thinner portions and store in refrigerator 5) Blast chiller 6) Any combination of the above. Use the following approved methods provided on the rapid cooling guideline., 113952, 113953.3, 113953.4, 113961, 113973 - Properly wash hands with hand soap and warm water for a minimum of 10 seconds at the hand washing station when beginning work; before handling food/equipment/utensils; as often as necessary during food preparation to remove soil and contamination; switching from working with raw to ready-to-eat foods; after touching body parts; after using toilet room; contamination of hands occurs. Food employees shall minimize contact with exposed, ready-to-eat food with their bare hands and shall use suitable utensils, gloves, or dispensing equipment., 114047, 114049, 114051, 114053, 114055, 114069(b) - Elevate all food at least 6 inches off of the floor to prevent contamination. Properly label bulk ingredient/food containers with common name., 114135, 114185.1 114185.3 [d-e] - Store wiping cloths used to wipe service counters, scales, or other surfaces that may come into contact with food in clean water with sanitizer or use only once; separate sanitizing containers shall be provided for wiping cloths used with raw animal foods., 114074, 114081, 114119, 114121, 114161, 114178, 114179, 114083, 114185, 114185.2, 114185.3, 114185.4, 114185.5 - All clean and soiled linen shall be properly stored; non-food items shall be stored and displayed separate from food and food-contact surfaces. Utensils and equipment shall be handled and stored so as to be protected from contamination., 113947.1-113947.6, 113948 - Obtain a state approved food safety certification course within 60 days of operation or when a Food Safety Manager has left the facility. Maintain copies of food safety certificates (food safety manager and food handler cards) on site., 114171, 114189.1, 114190, 114192, 114193, 114193.1, 114199, 114201, 114269 - Protect the potable water supply with a backflow protection device, as required by applicable plumbing codes. All plumbing, plumbing fixtures, and grease interceptors shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Any hose used for conveying potable water shall be of approved materials, labeled, properly stored, and used for no other purpose., - Food, equipment, or utensils that are found to be unsanitary or in disrepair may be Voluntarily Condemned and Destroyed by the person in charge.

December 19, 2025

Pass

P

114157Maintain onsite an accurate, easily readable metal probe thermometer suitable for measuring temperature of food shall be available. A display thermometer +/- 2F shall be provided for each hot and cold holding unit of potentially hazardous foods and high temperature warewashing machines., 113996, 113998, 114037, 114429, 114429.3, 114429.5 - Keep potentially hazardous foods (PHF) cold at 41°F or below or hot held at 135°F or above. Immediately discontinue storing PHF at room temperature., 113953, 113953.1, 113953.2, 114067(f) - Provide soap and single-use towels in dispensers, or a drying device at each handwash sink at all times. Maintain all handwash sinks unobstructed and accessible at all times., 114067(h), 114123, 114143(a, b), 114256-114256.2, 114256.4, 114257-114257.1, 114259, 114259.2-114259.3, 114279, 114281, 114282 - Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 113953(c), 114163(a)(3), 114189, 114192.1, 114195, 114279 - Immediately provide hot running potable water of at least 120°F or greater for the entire food preparation facility., 113984(d), 114097, 114099.1, 114099.4, 114099.6, 114101(b, c, d), 114105, 114109, 114111, 114113, 11415 (a, b, D), 114117, 114125(b), 114141 - Properly wash, rinse and sanitize all food contact surfaces. Make a 100 ppm bleach sanitizing solution or a 200 ppm quaternary ammonia solution for the third compartment., - Submit additional documents as instructed., 114002, 114002.1 - Rapidly cool potentially hazardous foods from 135°F to 70°F within 2 hours, then from 70°F to 41°F within 4 hours. Discontinue cooling PHF's at room temperature. Rapid cool by any of the following approved methods: 1) Ice water bath 2) Ice wand 3) Shallow stainless steel pans filled 2-3 inches and store in refrigerator 4) Separate into smaller or thinner portions and store in refrigerator 5) Blast chiller 6) Any combination of the above. Use the following approved methods provided on the rapid cooling guideline., 113952, 113953.3, 113953.4, 113961, 113973 - Properly wash hands with hand soap and warm water for a minimum of 10 seconds at the hand washing station when beginning work; before handling food/equipment/utensils; as often as necessary during food preparation to remove soil and contamination; switching from working with raw to ready-to-eat foods; after touching body parts; after using toilet room; contamination of hands occurs. Food employees shall minimize contact with exposed, ready-to-eat food with their bare hands and shall use suitable utensils, gloves, or dispensing equipment., 114047, 114049, 114051, 114053, 114055, 114069(b) - Elevate all food at least 6 inches off of the floor to prevent contamination. Properly label bulk ingredient/food containers with common name., 114135, 114185.1 114185.3 [d-e] - Store wiping cloths used to wipe service counters, scales, or other surfaces that may come into contact with food in clean water with sanitizer or use only once; separate sanitizing containers shall be provided for wiping cloths used with raw animal foods., 114074, 114081, 114119, 114121, 114161, 114178, 114179, 114083, 114185, 114185.2, 114185.3, 114185.4, 114185.5 - All clean and soiled linen shall be properly stored; non-food items shall be stored and displayed separate from food and food-contact surfaces. Utensils and equipment shall be handled and stored so as to be protected from contamination., 113947.1-113947.6, 113948 - Obtain a state approved food safety certification course within 60 days of operation or when a Food Safety Manager has left the facility. Maintain copies of food safety certificates (food safety manager and food handler cards) on site., 114171, 114189.1, 114190, 114192, 114193, 114193.1, 114199, 114201, 114269 - Protect the potable water supply with a backflow protection device, as required by applicable plumbing codes. All plumbing, plumbing fixtures, and grease interceptors shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Any hose used for conveying potable water shall be of approved materials, labeled, properly stored, and used for no other purpose., - Food, equipment, or utensils that are found to be unsanitary or in disrepair may be Voluntarily Condemned and Destroyed by the person in charge.

114159Maintain onsite an accurate, easily readable metal probe thermometer suitable for measuring temperature of food shall be available. A display thermometer +/- 2F shall be provided for each hot and cold holding unit of potentially hazardous foods and high temperature warewashing machines., 113996, 113998, 114037, 114429, 114429.3, 114429.5 - Keep potentially hazardous foods (PHF) cold at 41°F or below or hot held at 135°F or above. Immediately discontinue storing PHF at room temperature., 113953, 113953.1, 113953.2, 114067(f) - Provide soap and single-use towels in dispensers, or a drying device at each handwash sink at all times. Maintain all handwash sinks unobstructed and accessible at all times., 114067(h), 114123, 114143(a, b), 114256-114256.2, 114256.4, 114257-114257.1, 114259, 114259.2-114259.3, 114279, 114281, 114282 - Keep clean and free of litter or rubbish the premises of each food facility; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept vermin proof; open-air barbecues shall be operated in an approved manner., 113953(c), 114163(a)(3), 114189, 114192.1, 114195, 114279 - Immediately provide hot running potable water of at least 120°F or greater for the entire food preparation facility., 113984(d), 114097, 114099.1, 114099.4, 114099.6, 114101(b, c, d), 114105, 114109, 114111, 114113, 11415 (a, b, D), 114117, 114125(b), 114141 - Properly wash, rinse and sanitize all food contact surfaces. Make a 100 ppm bleach sanitizing solution or a 200 ppm quaternary ammonia solution for the third compartment., - Submit additional documents as instructed., 114002, 114002.1 - Rapidly cool potentially hazardous foods from 135°F to 70°F within 2 hours, then from 70°F to 41°F within 4 hours. Discontinue cooling PHF's at room temperature. Rapid cool by any of the following approved methods: 1) Ice water bath 2) Ice wand 3) Shallow stainless steel pans filled 2-3 inches and store in refrigerator 4) Separate into smaller or thinner portions and store in refrigerator 5) Blast chiller 6) Any combination of the above. Use the following approved methods provided on the rapid cooling guideline., 113952, 113953.3, 113953.4, 113961, 113973 - Properly wash hands with hand soap and warm water for a minimum of 10 seconds at the hand washing station when beginning work; before handling food/equipment/utensils; as often as necessary during food preparation to remove soil and contamination; switching from working with raw to ready-to-eat foods; after touching body parts; after using toilet room; contamination of hands occurs. Food employees shall minimize contact with exposed, ready-to-eat food with their bare hands and shall use suitable utensils, gloves, or dispensing equipment., 114047, 114049, 114051, 114053, 114055, 114069(b) - Elevate all food at least 6 inches off of the floor to prevent contamination. Properly label bulk ingredient/food containers with common name., 114135, 114185.1 114185.3 [d-e] - Store wiping cloths used to wipe service counters, scales, or other surfaces that may come into contact with food in clean water with sanitizer or use only once; separate sanitizing containers shall be provided for wiping cloths used with raw animal foods., 114074, 114081, 114119, 114121, 114161, 114178, 114179, 114083, 114185, 114185.2, 114185.3, 114185.4, 114185.5 - All clean and soiled linen shall be properly stored; non-food items shall be stored and displayed separate from food and food-contact surfaces. Utensils and equipment shall be handled and stored so as to be protected from contamination., 113947.1-113947.6, 113948 - Obtain a state approved food safety certification course within 60 days of operation or when a Food Safety Manager has left the facility. Maintain copies of food safety certificates (food safety manager and food handler cards) on site., 114171, 114189.1, 114190, 114192, 114193, 114193.1, 114199, 114201, 114269 - Protect the potable water supply with a backflow protection device, as required by applicable plumbing codes. All plumbing, plumbing fixtures, and grease interceptors shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Any hose used for conveying potable water shall be of approved materials, labeled, properly stored, and used for no other purpose., - Food, equipment, or utensils that are found to be unsanitary or in disrepair may be Voluntarily Condemned and Destroyed by the person in charge.

May 21, 2025

Pass

P

114193An air gap between the water supply inlet and the flood level rim of the plumbing fixture shall be at least twice the diameter of the water supply inlet and may not be less than 1 inch., 113953, 113953(b) - Hand sinks shall be sufficient in number and conveniently located so as to be accessible at all times., 114266, 114257, 114257.1, 114259 - A food facility shall at all times be constructed, equipped, and maintained, and operated as to prevent the entrance and harborage of animals, birds, and vermin, including, but not limited to rodents and insects., 114060 - Food on display shall be protected from contamination by approved a sneeze guard (e.g. vertical glass sneezeguard 60" Above Finished Floor)., 114193, 114193.1, 114269 - Equipment that discharges liquid waste, e.g. food preparation sinks, dishwashing machines, steam tables, ice machines and bins, espresso machines, walk-in refrigeration units, shall have approved indirect drainage through an air gap into a floor sink or other approved receiving vessel., 114130, 114169 - All new and used equipment and utensils shall be certified or classified for sanitation by an American National Standards Institute (ANSI) accredited certification program, e.g. NSF, ETL Sanitation, UL Sanitation, CSA Sanitation. , 114244, 114245 - Provide a floor plan showing the path-of-travel to the refuse storage area., 114271 - Wall and ceiling finish shall be smooth, durable, easily cleanable, and non-absorbent in all areas where there is food service or preparation, open food storage, warewashing, janitorial service, trash storage, and employee restrooms., 114279, 114281, 114282 - At least one curbed cleaning facility or janitorial sink equipped with hot and cold water and a drain shall be provided and conveniently located., 114268 - The floor finish shall be smooth, durable, easily cleanable, and non-absorbent in all areas where there is food service or preparation, open food storage, warewashing, janitorial service, trash storage, and employee restrooms., 114276, 114149, SF Health Code Section 440.5 - A permanent food facility shall provide clean toilet facilities in good repair for use by employees., 114130, 114169 - All equipment shall be installed on castors, six (6) inch high round metal legs, or on a minimum four (4) inch high curb or pedestal with a continuously coved base at the juncture., 114268 - Floor surfaces shall be coved at the juncture of the floor and wall with a 3/8 inch minimum radius coving and shall extend up the wall at least 4 inches.

114193.1An air gap between the water supply inlet and the flood level rim of the plumbing fixture shall be at least twice the diameter of the water supply inlet and may not be less than 1 inch., 113953, 113953(b) - Hand sinks shall be sufficient in number and conveniently located so as to be accessible at all times., 114266, 114257, 114257.1, 114259 - A food facility shall at all times be constructed, equipped, and maintained, and operated as to prevent the entrance and harborage of animals, birds, and vermin, including, but not limited to rodents and insects., 114060 - Food on display shall be protected from contamination by approved a sneeze guard (e.g. vertical glass sneezeguard 60" Above Finished Floor)., 114193, 114193.1, 114269 - Equipment that discharges liquid waste, e.g. food preparation sinks, dishwashing machines, steam tables, ice machines and bins, espresso machines, walk-in refrigeration units, shall have approved indirect drainage through an air gap into a floor sink or other approved receiving vessel., 114130, 114169 - All new and used equipment and utensils shall be certified or classified for sanitation by an American National Standards Institute (ANSI) accredited certification program, e.g. NSF, ETL Sanitation, UL Sanitation, CSA Sanitation. , 114244, 114245 - Provide a floor plan showing the path-of-travel to the refuse storage area., 114271 - Wall and ceiling finish shall be smooth, durable, easily cleanable, and non-absorbent in all areas where there is food service or preparation, open food storage, warewashing, janitorial service, trash storage, and employee restrooms., 114279, 114281, 114282 - At least one curbed cleaning facility or janitorial sink equipped with hot and cold water and a drain shall be provided and conveniently located., 114268 - The floor finish shall be smooth, durable, easily cleanable, and non-absorbent in all areas where there is food service or preparation, open food storage, warewashing, janitorial service, trash storage, and employee restrooms., 114276, 114149, SF Health Code Section 440.5 - A permanent food facility shall provide clean toilet facilities in good repair for use by employees., 114130, 114169 - All equipment shall be installed on castors, six (6) inch high round metal legs, or on a minimum four (4) inch high curb or pedestal with a continuously coved base at the juncture., 114268 - Floor surfaces shall be coved at the juncture of the floor and wall with a 3/8 inch minimum radius coving and shall extend up the wall at least 4 inches.

114269An air gap between the water supply inlet and the flood level rim of the plumbing fixture shall be at least twice the diameter of the water supply inlet and may not be less than 1 inch., 113953, 113953(b) - Hand sinks shall be sufficient in number and conveniently located so as to be accessible at all times., 114266, 114257, 114257.1, 114259 - A food facility shall at all times be constructed, equipped, and maintained, and operated as to prevent the entrance and harborage of animals, birds, and vermin, including, but not limited to rodents and insects., 114060 - Food on display shall be protected from contamination by approved a sneeze guard (e.g. vertical glass sneezeguard 60" Above Finished Floor)., 114193, 114193.1, 114269 - Equipment that discharges liquid waste, e.g. food preparation sinks, dishwashing machines, steam tables, ice machines and bins, espresso machines, walk-in refrigeration units, shall have approved indirect drainage through an air gap into a floor sink or other approved receiving vessel., 114130, 114169 - All new and used equipment and utensils shall be certified or classified for sanitation by an American National Standards Institute (ANSI) accredited certification program, e.g. NSF, ETL Sanitation, UL Sanitation, CSA Sanitation. , 114244, 114245 - Provide a floor plan showing the path-of-travel to the refuse storage area., 114271 - Wall and ceiling finish shall be smooth, durable, easily cleanable, and non-absorbent in all areas where there is food service or preparation, open food storage, warewashing, janitorial service, trash storage, and employee restrooms., 114279, 114281, 114282 - At least one curbed cleaning facility or janitorial sink equipped with hot and cold water and a drain shall be provided and conveniently located., 114268 - The floor finish shall be smooth, durable, easily cleanable, and non-absorbent in all areas where there is food service or preparation, open food storage, warewashing, janitorial service, trash storage, and employee restrooms., 114276, 114149, SF Health Code Section 440.5 - A permanent food facility shall provide clean toilet facilities in good repair for use by employees., 114130, 114169 - All equipment shall be installed on castors, six (6) inch high round metal legs, or on a minimum four (4) inch high curb or pedestal with a continuously coved base at the juncture., 114268 - Floor surfaces shall be coved at the juncture of the floor and wall with a 3/8 inch minimum radius coving and shall extend up the wall at least 4 inches.

May 21, 2025

Pass

P

114193An air gap between the water supply inlet and the flood level rim of the plumbing fixture shall be at least twice the diameter of the water supply inlet and may not be less than 1 inch., 113953, 113953(b) - Hand sinks shall be sufficient in number and conveniently located so as to be accessible at all times., 114266, 114257, 114257.1, 114259 - A food facility shall at all times be constructed, equipped, and maintained, and operated as to prevent the entrance and harborage of animals, birds, and vermin, including, but not limited to rodents and insects., 114060 - Food on display shall be protected from contamination by approved a sneeze guard (e.g. vertical glass sneezeguard 60" Above Finished Floor)., 114193, 114193.1, 114269 - Equipment that discharges liquid waste, e.g. food preparation sinks, dishwashing machines, steam tables, ice machines and bins, espresso machines, walk-in refrigeration units, shall have approved indirect drainage through an air gap into a floor sink or other approved receiving vessel., 114130, 114169 - All new and used equipment and utensils shall be certified or classified for sanitation by an American National Standards Institute (ANSI) accredited certification program, e.g. NSF, ETL Sanitation, UL Sanitation, CSA Sanitation. , 114244, 114245 - Provide a floor plan showing the path-of-travel to the refuse storage area., 114271 - Wall and ceiling finish shall be smooth, durable, easily cleanable, and non-absorbent in all areas where there is food service or preparation, open food storage, warewashing, janitorial service, trash storage, and employee restrooms., 114279, 114281, 114282 - At least one curbed cleaning facility or janitorial sink equipped with hot and cold water and a drain shall be provided and conveniently located., 114268 - The floor finish shall be smooth, durable, easily cleanable, and non-absorbent in all areas where there is food service or preparation, open food storage, warewashing, janitorial service, trash storage, and employee restrooms., 114276, 114149, SF Health Code Section 440.5 - A permanent food facility shall provide clean toilet facilities in good repair for use by employees., 114130, 114169 - All equipment shall be installed on castors, six (6) inch high round metal legs, or on a minimum four (4) inch high curb or pedestal with a continuously coved base at the juncture., 114268 - Floor surfaces shall be coved at the juncture of the floor and wall with a 3/8 inch minimum radius coving and shall extend up the wall at least 4 inches.

114193.1An air gap between the water supply inlet and the flood level rim of the plumbing fixture shall be at least twice the diameter of the water supply inlet and may not be less than 1 inch., 113953, 113953(b) - Hand sinks shall be sufficient in number and conveniently located so as to be accessible at all times., 114266, 114257, 114257.1, 114259 - A food facility shall at all times be constructed, equipped, and maintained, and operated as to prevent the entrance and harborage of animals, birds, and vermin, including, but not limited to rodents and insects., 114060 - Food on display shall be protected from contamination by approved a sneeze guard (e.g. vertical glass sneezeguard 60" Above Finished Floor)., 114193, 114193.1, 114269 - Equipment that discharges liquid waste, e.g. food preparation sinks, dishwashing machines, steam tables, ice machines and bins, espresso machines, walk-in refrigeration units, shall have approved indirect drainage through an air gap into a floor sink or other approved receiving vessel., 114130, 114169 - All new and used equipment and utensils shall be certified or classified for sanitation by an American National Standards Institute (ANSI) accredited certification program, e.g. NSF, ETL Sanitation, UL Sanitation, CSA Sanitation. , 114244, 114245 - Provide a floor plan showing the path-of-travel to the refuse storage area., 114271 - Wall and ceiling finish shall be smooth, durable, easily cleanable, and non-absorbent in all areas where there is food service or preparation, open food storage, warewashing, janitorial service, trash storage, and employee restrooms., 114279, 114281, 114282 - At least one curbed cleaning facility or janitorial sink equipped with hot and cold water and a drain shall be provided and conveniently located., 114268 - The floor finish shall be smooth, durable, easily cleanable, and non-absorbent in all areas where there is food service or preparation, open food storage, warewashing, janitorial service, trash storage, and employee restrooms., 114276, 114149, SF Health Code Section 440.5 - A permanent food facility shall provide clean toilet facilities in good repair for use by employees., 114130, 114169 - All equipment shall be installed on castors, six (6) inch high round metal legs, or on a minimum four (4) inch high curb or pedestal with a continuously coved base at the juncture., 114268 - Floor surfaces shall be coved at the juncture of the floor and wall with a 3/8 inch minimum radius coving and shall extend up the wall at least 4 inches.

114269An air gap between the water supply inlet and the flood level rim of the plumbing fixture shall be at least twice the diameter of the water supply inlet and may not be less than 1 inch., 113953, 113953(b) - Hand sinks shall be sufficient in number and conveniently located so as to be accessible at all times., 114266, 114257, 114257.1, 114259 - A food facility shall at all times be constructed, equipped, and maintained, and operated as to prevent the entrance and harborage of animals, birds, and vermin, including, but not limited to rodents and insects., 114060 - Food on display shall be protected from contamination by approved a sneeze guard (e.g. vertical glass sneezeguard 60" Above Finished Floor)., 114193, 114193.1, 114269 - Equipment that discharges liquid waste, e.g. food preparation sinks, dishwashing machines, steam tables, ice machines and bins, espresso machines, walk-in refrigeration units, shall have approved indirect drainage through an air gap into a floor sink or other approved receiving vessel., 114130, 114169 - All new and used equipment and utensils shall be certified or classified for sanitation by an American National Standards Institute (ANSI) accredited certification program, e.g. NSF, ETL Sanitation, UL Sanitation, CSA Sanitation. , 114244, 114245 - Provide a floor plan showing the path-of-travel to the refuse storage area., 114271 - Wall and ceiling finish shall be smooth, durable, easily cleanable, and non-absorbent in all areas where there is food service or preparation, open food storage, warewashing, janitorial service, trash storage, and employee restrooms., 114279, 114281, 114282 - At least one curbed cleaning facility or janitorial sink equipped with hot and cold water and a drain shall be provided and conveniently located., 114268 - The floor finish shall be smooth, durable, easily cleanable, and non-absorbent in all areas where there is food service or preparation, open food storage, warewashing, janitorial service, trash storage, and employee restrooms., 114276, 114149, SF Health Code Section 440.5 - A permanent food facility shall provide clean toilet facilities in good repair for use by employees., 114130, 114169 - All equipment shall be installed on castors, six (6) inch high round metal legs, or on a minimum four (4) inch high curb or pedestal with a continuously coved base at the juncture., 114268 - Floor surfaces shall be coved at the juncture of the floor and wall with a 3/8 inch minimum radius coving and shall extend up the wall at least 4 inches.

May 14, 2025

Pass

P

May 14, 2025

Pass

P

March 26, 2025

Complaint (I)

Pass

P

Inspection History